--- title: "Configuring the SMTP interface with an IP Address using the CLI" slug: "configuring-the-smtp-interface-with-an-ip-address-using-the-cli" tags: ["Product Usage", "EX 11.x", "FX 11.x", "AX 11.x", "NX 11.x", "Network Security"] updated: 2026-08-24T19:53:10Z published: 2026-08-24T19:53:10Z canonical: "docs.trellix.com/configuring-the-smtp-interface-with-an-ip-address-using-the-cli" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring the SMTP interface with an IP Address using the CLI Use the CLI commands in this procedure to configure the SMTP (pether3) interface with an IP address and mask length. > [!WARNING] > Important > > Do not use the `interface pether3 ipv6 address` command to configure the SMTP (pether3) interface. **To configure the SMTP interface with an IP address:** 1. Go to CLI configuration mode. ``` hostname > enable hostname # configure terminal ``` 2. Specify the IPv4 address and mask length for the pether3 interface. `hostname (config) # interface pether3 ip address <IPv4_address> <mask_length>` 3. Specify the static IPv6 address and mask length for the pether3 interface. `hostname (config) # email-analysis interface pether3 ipv6 address <IPv6_address> mask-len <mask_length>` 4. Verify your configuration for the IPv4 address and mask length for the pether3 interface. `hostname (config) # show interface pether3 configured` 5. Verify your configuration for the static IPv6 address and mask length for the pether3 interface. `hostname (config) # show ipv6 route` 6. Save your changes. ``` hostname (config) # write memory ``` ### Example This example shows how to configure the IPv4 address and mask length for the SMTP (pether3) interface. `hostname (config) # interface pether3 ip address 172.17.74.68 /12` `hostname (config) # show interface pether3 configured` ``` Interface pether3 configuration: ``` ```   Comment: ``` ```   Enabled:            yes ``` ```   DHCP:               no ``` ```   Zeroconf:           no ``` ```   IP address:         172.17.74.68 ``` ```   Netmask:            255.240.0.0 ``` ```   IPv6 enabled:       yes ``` ```   Autoconf enabled:   no ``` ```   Autoconf route:     yes ``` ```   Autoconf privacy:   no ``` ```   DHCPv6 enabled:     no ``` ```   IPv6 addresses:     3 ``` ```   IPv6 address:       2001:470:84a7:1720:20c:bdff:fe04:9f73/5 ``` ```   IPv6 address:       2001:470:84a7:1720:20c:bdff:fe04:9f74/5 ``` ```   IPv6 address:       2001:470:84a7:1720:20c:bdff:fe04:9f75/5 ``` ```   ..... ``` This example shows how to configure the static IPv6 address and mask length for the pether3 interface. `hostname (config) # email-analysis interface pether3 ipv6 address 2001:470:84a7:1720:bdff:fe049f77 mask-len 64` `hostname (config) # show ipv6 route` `Destination prefix` `Gateway Interface Source` `-----------------------------------------------------------------------` `::1/128` `:: lo local` ``` 2001:470:84a7:1720::/64 ``` `:: pether3 interface` `2001:470:84a7:1720:225:90ff:fef3:2476/128` `:: lo local`