--- title: "Configuration wizard steps" slug: "configuration-wizard-steps" tags: ["HX 11.x", "Endpoint Security (HX)", "Product Usage"] updated: 2026-09-10T15:49:39Z published: 2026-09-10T15:49:39Z canonical: "docs.trellix.com/configuration-wizard-steps" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuration wizard steps The following table describes the questions the configuration wizard prompts you to answer. As noted in the table, the wizard skips some steps based on your answers to previous steps and whether initial settings were specified on the **Properties** screen for ESXi virtual servers or in the `set_keys.ps1` PowerShell script for Hyper-V virtual servers. ### Note Press Ctrl+C to exit the configuration wizard. After the management interface is configured, an administrator can use the `configuration jump-start` CLI command to run the wizard again. | Step | Response | | --- | --- | | Enter activation code? | Enter the activation code you obtained from Trellix. You will not be prompted for an activation code if you supplied one on the **Properties** screen for ESXi virtual servers or in the `set_keys.ps1` PowerShell script for Hyper-V virtual servers. | | Hostname? | Enter the hostname for the server. You will not be prompted for the server hostname if you supplied one in the `set_keys.ps1` PowerShell script for Hyper-V virtual servers. | | Admin password? | Enter a new administrator password. The new password must be from 8–32 characters. You do not need to supply an updated admin password if you supplied one on the **Properties** screen for ESXi virtual servers or in the `set_keys.ps1` PowerShell script for Hyper-V virtual servers. **NOTE—**If you have not changed the admin password, do so now or the administrator will be unable to log in to the server. | | Confirm admin password? | Re-enter the new administrator password, if you supplied one in the previous step. | | Enable remote access for ‘admin’ user? | Enter **yes** to enable the administrator to log in to the server remotely. Enter **no** to disable remote access. | | Use DHCP on ether1 interface? | Enter **yes** to use Dynamic Host Configuration Protocol (DHCP) to configure the server IP address and other network parameters. Enter **no** to manually configure your IP address and network settings. (If you enter **yes**, the zeroconf and static IP addressing steps are skipped.) | | Use zeroconf on ether1 interface? | Enter **yes** to use zero-configuration (zeroconf) networking. Enter **no** to specify a static IP address and network mask. (If you specify **yes**, the next step is skipped.) **NOTE**: Do not use zeroconf on the primary interface. | | Primary IPv4 address and masklen? | Enter the IP address for the management interface in A.B.C.D format and enter the network mask, for example: 1.1.1.2/12. | | Default gateway? | Enter the gateway IP address for the management interface. | | Primary DNS server? | Enter the IP address of the DNS server. | | Domain name? | Enter the domain for the management interface; for example: **it.acme.com**. | | Enable fenet service? | Enter **yes** to enable access to the DTI network. (If you enter **no**, the next three steps are skipped.) | | Enable fenet license update service? | Enter **yes** to enable the licensing service to automatically download your licenses from the DTI network and install them. (If licenses are downloaded and installed successfully, the wizard skips the step that prompts for the product license key and the step that prompts for the security-content updates key.) | | Sync appliance time with fenet? | Enter **yes** to synchronize the server time with the DTI server time. If you enabled the licensing service, synchronization prevents a feature from being temporarily unlicensed due to a time gap. The wizard makes three attempts to perform this step before it gives up and moves to the next step. | | Update licenses from fenet? | Enter **yes** to download and install your licenses. The wizard makes three attempts to perform this step before giving up and moving on to the next step. | | Enable NTP? | Enter **yes** to enable automatic time synchronization with one or more Network Time Protocol (NTP) servers. | | Enable IPv6? | Enter **no** if you want to use IPv4 for your Endpoint Security (HX) virtual server or enter **yes** to enable IPv6 for your Endpoint Security (HX) virtual server. | | Product license key? | Press Enter to install a 15-day evaluation license. | :