--- title: "Install and configure SNMP for EDR Telemetry Store" slug: "install-and-configure-snmp-for-edr-telemetry-store" tags: ["EDR with Forensics (EDRF)", "Endpoint Security"] updated: 2026-08-26T19:31:16Z published: 2026-08-26T19:31:16Z canonical: "docs.trellix.com/install-and-configure-snmp-for-edr-telemetry-store" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Install and configure SNMP for EDR Telemetry Store Simple Network Management Protocol (SNMP) monitoring allows you to track the health and status of EDR Telemetry Store virtual appliances. SNMP is not enabled by default. You can install the SNMP service using bundled packages for offline environments or via standard repositories if the appliance has internet access. When installed, configure the service for **SNMP v2c** or **SNMP v3** to enable monitoring. ### Install the SNMP service To perform the installation, you must first access the system shell. 1. Log in to the appliance as admin. 2. Type `enable` and enter the password. 3. Type `shell`. 4. Run the command corresponding to your environment type: - **Offline or Air-gapped installation**: Install the bundled packages located in `/opt/trellix/optional_packages/snmp/`. ``` dnf --disablerepo='*' install /opt/trellix/optional_packages/snmp/*.rpm ``` - **Online installation**: If the appliance has internet access or can connect to the AlmaLinux package repositories, use the standard package manager. ``` dnf install net-snmp net-snmp-utils ``` ### Configure the SNMP service Configure the SNMP service based on your specific monitoring requirements (SNMP v2c or SNMP v3). The actual configuration is specific to each environment. **Prerequisite** Create a backup of the existing configuration file before making changes. ``` cp /etc/snmp/snmpd.conf /etc/snmp/snmpd.conf.backup ``` ###### Configure SNMP v2c 1. Edit the `snmpd` configuration file. ``` vi /etc/snmp/snmpd.conf ``` 2. Replace the content of `/etc/snmp/snmpd.conf` with the following example configuration: > [!NOTE] > Note > > The community strings below (`idv90we3rnov90wer` and `209ijvfwer0df92jd`) are examples. Replace them with secure strings specific to your environment. ``` # Map 'idv90we3rnov90wer' community to the 'ConfigUser' # Map '209ijvfwer0df92jd' community to the 'AllUser' # sec.name source community com2sec ConfigUser default idv90we3rnov90wer com2sec AllUser default 209ijvfwer0df92jd # Map 'ConfigUser' to 'ConfigGroup' for SNMP Version 2c # Map 'AllUser' to 'AllGroup' for SNMP Version 2c # sec.model sec.name group ConfigGroup v2c ConfigUser group AllGroup v2c AllUser # Define 'SystemView', which includes everything under .1.3.6.1.2.1.1 (or .1.3.6.1.2.1.25.1) # Define 'AllView', which includes everything under .1 # incl/excl subtree view SystemView included .1.3.6.1.2.1.1 view SystemView included .1.3.6.1.2.1.25.1.1 view AllView included .1 # Give 'ConfigGroup' read access to objects in the view 'SystemView' # Give 'AllGroup' read access to objects in the view 'AllView' # context model level prefix read write notify access ConfigGroup "" any noauth exact SystemView none none access AllGroup "" any noauth exact AllView none none dontLogTCPWrappersConnects yes ``` 3. Start and enable the SNMP service. ``` systemctl start snmpd systemctl enable snmpd ``` 4. Open the firewall to allow UDP traffic on port 161. ``` firewall-cmd --add-port=161/udp --permanent firewall-cmd --reload ``` 5. Run the `snmpwalk` command locally on the appliance to verify that metrics are accessible. **General verification** ``` # Show monitoring information for Config User snmpwalk -v 2c -c idv90we3rnov90wer -O e 127.0.0.1 # Show monitoring information for All User snmpwalk -v 2c -c 209ijvfwer0df92jd -O e 127.0.0.1 ``` **View specific metrics** Run the following commands to view specific system statistics (CPU, Memory, and System Load). **CPU Statistics** ``` snmpwalk -v2c -c 209ijvfwer0df92jd 127.0.0.1 .1.3.6.1.4.1.2021.11 ``` **Memory Statistics** ``` snmpwalk -v2c -c 209ijvfwer0df92jd 127.0.0.1 .1.3.6.1.4.1.2021.4 ``` **System Load Average** ``` snmpwalk -v2c -c 209ijvfwer0df92jd 127.0.0.1 .1.3.6.1.4.1.2021.10 ``` ###### Configure SNMP v3 1. Stop the SNMP service if it is running. ``` systemctl stop snmpd ``` 2. Create the SNMP v3 users. > [!NOTE] > Note > > Replace `AUTHENTICATION_PASSWORD`, `ENCRYPTION_PASSWORD`, `ADMIN_AUTHENTICATION_PASSWORD`, and `ADMIN_ENCRYPTION_PASSWORD` in the commands below with strong passwords or passphrases. ``` net-snmp-create-v3-user -ro -A "AUTHENTICATION_PASSWORD" -X "ENCRYPTION_PASSWORD" -a SHA -x AES SnmpRoUser net-snmp-create-v3-user -ro -A "ADMIN_AUTHENTICATION_PASSWORD" -X "ADMIN_ENCRYPTION_PASSWORD" -a SHA -x AES SnmpRoAdmin ``` 3. Edit the `snmpd` configuration file. ``` vi /etc/snmp/snmpd.conf ``` 4. Replace the content of `/etc/snmp/snmpd.conf` with the following configuration: ``` rouser SnmpRoUser priv .1.3.6.1.2.1.1 rouser SnmpRoUser priv .1.3.6.1.2.1.25.1.1 rouser SnmpRoAdmin priv .1 dontLogTCPWrappersConnects yes ``` 5. Restart and enable the SNMP service. ``` systemctl restart snmpd systemctl enable snmpd ``` 6. Open the firewall to allow UDP traffic on port 161. ``` firewall-cmd --add-port=161/udp --permanent firewall-cmd --reload ``` 7. Use `snmpwalk` to verify user access. ``` # Test SnmpRoUser (limited view) snmpwalk -v3 -l authPriv -u SnmpRoUser -a SHA -A "AUTHENTICATION_PASSWORD" -x AES -X "ENCRYPTION_PASSWORD" 127.0.0.1 .1.3.6.1.2.1.1 # Test SnmpRoAdmin (full view) snmpwalk -v3 -l authPriv -u SnmpRoAdmin -a SHA -A "ADMIN_AUTHENTICATION_PASSWORD" -x AES -X "ADMIN_ENCRYPTION_PASSWORD" 127.0.0.1 .1.3.6.1.4.1.2021.11 ```