--- title: "Rogue System Detection 5.0.7 Installation Guide" slug: "rogue-system-detection-5-0-7-installation-guide" tags: ["Rogue System Detection", "Install and Get Started"] updated: 2026-09-10T08:01:03Z published: 2026-09-10T08:01:03Z canonical: "docs.trellix.com/rogue-system-detection-5-0-7-installation-guide" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Rogue System Detection 5.0.7 Installation Guide # **Considerations for installing** **Trellix RSD** When planning your deployment of **Trellix RSD 5.x**, it is important to consider how it affects existing **Trellix** products and how the policy works. ### Deployment of Trellix RSD 5.x sensors Although the **Trellix RSD 5.x** sensor technology continues to support deployment on DHCP servers, **Trellix** recommends that you deploy sensors on every subnet. This provides the best visibility of rogue systems, full coverage of the entire enterprise network, fastest detection time, and best accuracy for determining rogue device attributes, such as OS detection. ### Ports used for active detection Trellix RSD 5.x uses sensor technology to detect rogue systems. The sensor uses a combination of passive and active detection techniques. For active detection, the Rogue System Sensor (5.x) requires a smaller number of ports than previous releases. It attempts to use ports that are already known to be open or closed. Otherwise, it uses the following ports: - **TCP —** Ports 22, 80, 443, and 445. - **UDP —** Ports 65534, 65533, and 65532. The software selects the first unused port. ### Interaction with other Trellix products The Rogue System Sensor integrates with **Trellix Agent** on managed systems. The Rogue System Sensor 4.x integrates with the **McAfee® Rogue Database Detection (RDD)** sensor. The Rogue System Sensor 5.x does not support integration with RDD. If you use RDD, you can maintain existing 4.x sensors and deploy additional new Trellix RSD 5.x sensors. ### Use of WinPCap You cannot deploy the Rogue System Sensor to a system that is running WinPcap or any software using WinPcap. If WinPcap is installed, the sensor installation stops and logs an error message. If you install WinPcap on a system that already has a sensor installed, it can cause the sensor to stop functioning properly. ### Microsoft KB2563894 security update required on systems running the sensor Any system you install a sensor on requires the Microsoft KB2563894 security update. If the update is not present, the sensor installation stops and logs an error message. This update is required to fix an issue that can cause the system to stop responding due to network traffic types used by the Rogue System Sensor. --- 3 --- ## Trellix RSD policies **Trellix RSD** can simultaneously manage Rogue System Sensor versions 4.x and 5.x. **Trellix RSD** sends the same policy to all sensors. Some policy settings are relevant only for 4.x sensors, some for 5.x sensors, and some for all sensors. When a sensor receives a **Trellix RSD** policy from **Trellix ePO - On-prem**, it uses the policy settings that apply to its version. A revision number was added to the policy and to the server settings. This number can be used to easily identify which specific policy and server setting versions are applied to a specific sensor. ## Internal database Rogue System Sensor 5.x maintains a state of all detected and profiled systems on the network that is encrypted for security. The encryption key is unique for each **Trellix RSD** installation. If you uninstall and then reinstall **Trellix RSD**, the software generates a new encryption key. This means that all managed sensors drop their existing database, create a new database, and redetect the systems on the network. To prevent the extra load and network traffic, avoid uninstalling and reinstalling **Trellix RSD** unless required or instructed by **Trellix support**. ## Sensor components and log files Rogue System Sensor 5.x is designed to detect rogue systems for its local subnet only. It runs two components on the systems they are installed on: - RSDPP — A Windows service that is responsible for managing communications with **Trellix RSD** through the **Trellix Agent**. - Balash — A Windows process that is responsible for discovering and profiling devices operating on the network. Rogue System Sensor 5.x maintains two log files that can be used to solve issues: - rsdpp.log — The log file of the RSDPP service contains information about the sensor installation process and communications with **ePolicy Orchestrator** through the **Trellix Agent**. - balash.log — The log file of the Balash process contains information about the network detection performed by the sensor and the devices that were discovered and profiled. The **balash.log** file can contain sensitive information, such as the media access control addresses (MAC) and IP addresses of systems on the network. By default, the file contains only messages tagged with **Error** and **Critical** priority. For troubleshooting, you can gather more detailed information by setting the **Log File Settings** configuration on the policy's **General** tab to **Log all messages (recommended for troubleshooting and debugging)**. It is important to reset this configuration to the default level once you finish troubleshooting. --- # Getting started To configure **Trellix RSD**, you enable and set options on the **Server Settings** page, create policies, and install Rogue System Sensors on systems in the managed subnets. ## About policies *A policy* is a collection of settings that you create and configure, then enforce. **Trellix ePO - On-prem** organizes its policies by product, then by *categories* for each product. For example, the **Trellix Agent** product includes categories for **General**, **Repository**, and **Troubleshooting**. To see policies in a specific policy category, select **Menu** → **Policy** → **Policy Catalog**, then select a product from the Products pane and the corresponding categories appear on the right pane. Expand the category to see the list of policies. For example, you can increase the **Trellix ePO - On-prem** response time from the default value of every 60 minutes. To add time, change the agent-server communication interval (ASCI) for workstations in the **Trellix Agent** policy to every 240–360 minutes. To change the workstation ASCI setting, duplicate the **Trellix Agent**, **Trellix Default** policy, in the **General** category, and change the ASCI setting. Then you must assign the new policy to a **System Tree** group or tag that includes all those workstations. ## Considerations for policy settings Policy settings configure the features and performance of the Rogue System Sensor. These settings are separated into four groups: - Communication settings - Detection settings - General settings - Interface settings ### Communication settings Communication settings determine: - Active sensor election - Communication time for inactive sensors - Reporting time for active sensors - Sensor’s detected system cache lifetime The active sensor election settings determine if the active sensors are set using the **Trellix ePO - On-prem** server or allowing the sensors in the subnets themselves to elect which sensors are active or asleep. > ![Blue note icon with pencil](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0006_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) > > **Note** > > If you install Rogue System Sensors on many nodes on many subnets and configure the policy to **Use Local Sensor Election** and later change the policy to **Use ePO server** to determine active sensors, all those previously installed sensors could overwhelm the **Trellix ePO - On-prem** server asking if they should become active. The **communication time** for inactive sensors determines how often passive sensors check in with the server. The **Reporting time** for active sensors determines how often active sensors report to the **Trellix ePO - On-prem** server. Setting this value too low can have the same effect as setting the value for the sensor’s detected system cache lifetime. The sensor’s **detected system cache lifetime** is the amount of time a detected system remains in the sensor’s cache. This value controls how often the sensor reports that a system is newly detected. The lower the value, the more often the sensor reports a system detection to the server. Setting this value too low can overwhelm your server with system detections. Setting this value too high prevents you from having current information on system detections. > ![Lightbulb tip icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0006_img_02.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) > > **Tip** > > **Trellix** recommends that you set the same value for the sensor’s detected system cache lifetime and for the reporting time for active sensors settings. ## Detection settings Detection settings determine whether: - Device details detection is enabled - DHCP monitoring is enabled - Reporting on self-configured subnets is enabled If you use DHCP servers on your network, you can install sensors on them to monitor your network. This allows you to use a single sensor to report on all subnets and systems that connect to it. DHCP monitoring allows you to cover your network with fewer sensors to deploy and manage, and reduces the potential for missed subnets and systems. Device details detection allows you to specify the type of information the Rogue System Sensor scans systems for. - Operating System (OS) details — This option allows the sensor to determine detailed information about a device's operating system. If you enable OS details scanning, you can also choose to scan the systems you have marked as exceptions. - OS detection by choosing to scan all networks or only specific networks — You can limit OS detection to specific subnets by including or excluding specific IP addresses. The Rogue System Sensor uses NetBIOS calls and OS fingerprinting to provide more detailed information about the devices on your network. You can enable active probing on your entire network, or include or exclude specific subnets. --- > ![Caution triangular icon with exclamation mark](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0007_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) > > **Caution** > > This feature provides accurate matching of detected system interfaces and should be disabled only if you have specific reasons to do so. ### General settings General settings determine: - Sensor-to-server communication port - Server IP address or DNS name - Whether the Rogue System Sensor is enabled The server IP address default value is the address of the **Trellix ePO - On-prem** server that you are using to install sensors. **Trellix RSD** reports system detections to the specified server. When this server detects a system that has an agent deployed by a **Trellix ePO - On-prem** server with a different IP address, that system is detected as a rogue because the agent is considered an alien agent. > ![Note icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0007_img_02.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) > > **Note** > > The sensor-to-server communication port server setting can be changed only during installation. Whichever port you have specified during installation must also be specified on the **General** tab of Trellix RSD policies. ### Interface settings Interface settings determine whether sensors: - Don't listen on interfaces whose IP addresses are included in specific networks. - Only listen on an interface if its IP address is included on a network found during installation. - Only listen on interfaces whose IP addresses are included in specific networks. Specifying these settings allows you to choose the networks that the sensor reports on. ## Trellix RSD policy settings **Trellix RSD** policy settings allow you to configure and manage the instances of the Rogue System Sensor installed throughout your network. Settings can be applied to individual systems, groups of systems, and IP address ranges. You can configure policy settings for all sensors deployed by the server. This process is similar to managing policies for any deployed product. The **Trellix RSD** policy pages are installed on the **Trellix ePO - On-prem** server at installation. Groups or individual systems inherit policy settings that you assign to higher levels of the **System Tree**. --- Trellix Rogue System Detection 5.0.7 Installation Guide 7 --- > ![Blue lightbulb icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0008_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Tip** > > Trellix recommends that you configure policy settings before you deploy sensors to your network to make sure that the sensors work according to your intended use. For example, DHCP monitoring is disabled by default. If you deploy sensors to DHCP servers without enabling DHCP monitoring during your initial configuration, those sensors report limited information to the Trellix ePO - On-prem server. If you deploy sensors before you configure your policies, you can update them to change sensor functionality. # Configure Trellix RSD server and policy settings Confirm the default configuration of the **Trellix RSD** server settings. These server settings determine what a rogue system is, configure sensor settings, and more. The **Trellix RSD** policies are configured with default settings. However, these might not be the best settings to detect rogue systems on your **ePolicy Orchestrator** server or the most efficient settings for your network. ### Task 1. Click Menu → Policy → Policy Catalog, then from the Product drop-down list select Rogue System Detection, and from the Category drop-down list, select General. All created policies for Trellix RSD appear. 2. Click the My Default policy to start editing the policy. If you want to create a policy, click Actions → New Policy. 3. On the Communications tab, configure: - Sensor's detected system cache lifetime — You can increase this setting on large widely dispersed networks to reduce traffic on the subnet. > ![Pencil note icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0008_img_02.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Note** > > This section is relevant for 4.x sensors only. - Reporting time for active sensors — You can increase this setting on large widely dispersed networks to reduce traffic back to the **Trellix ePO - On-prem** server. - Active sensor election — These settings depend on the size and location of your subnets from the **Trellix ePO - On-prem** server. - On smaller networks, click **Use ePO server to determine active sensors**. You can probably leave the **Communication time for inactive sensors** at the default setting. - On large networks, click **Use Local Sensor Election**. - Configure active sensors as either: - **All sensors active** — The best selection for large networks with many subnets. --- > ![Blue/green triangular caution icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0009_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Caution** > > Be careful about installing Rogue System Sensors on many nodes on many subnets and configure the policy to **Use Local Sensor Election** and then later changing the policy to **Use ePO server to determine active sensors**. All previously installed sensors can overwhelm the **Trellix ePO - On-prem** server asking to become active. - **Set the number of active sensor(s)** — This is the manual configuration solution. - Configure these settings depending on the location and speed of the connection between the managed subnets and the **Trellix ePO - On-prem** server: - **Wait time for an election result** — You can increase this setting on slow networks to reduce traffic between sensors during the elections. > ![Blue note icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0009_img_02.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Note** > > This setting is relevant for 4.x sensors only. - **Wait time between active sensor elections** — You can increase this setting if you want elections to occur less frequently. - **Ipv4 multicast group or Ipv6 multicast group** — Used by the local election feature to send multicast messages. Only change the default address if another feature is using the default. - **Sensor-to-Sensor communication port** — Only change the default if another process is using the port. 1. **On the Interfaces tab,** you can configure specific IP address networks to scan or not to scan for rogue systems. For example, if you have a voice over IP subnet, you can add that subnet address to the Do not listen on list and the voice over IP phone systems are ignored as rogue systems. 2. **On the Detection tab, configure:** - **DHCP monitoring** — Specifies the settings for Dynamic Host Configuration Protocol (DHCP) monitoring. When DHCP monitoring is enabled, a single sensor installed on a DHCP server can monitor all systems and subnets that it serves. > ![Blue note icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0009_img_02.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Note** > > The Interfaces tab is relevant for 4.x sensors only. > ![Blue note icon](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0009_img_02.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Note** > > This setting is relevant for 4.x sensors only. --- > **Note** > > A DHCP server can't monitor interfaces with static IP addresses. - **Device details detection** — To access the information captured by this configuration, click **Menu → Systems Section → Detected Systems** and click any system that appears in the **Detected System Interfaces by Subnet.** > **Note** > > This setting is relevant for 4.x sensors only. > **Important** > > Enabling this feature might cause **Security Alerts** on local Firewalls, for example **OS Fingerprint equals Port Scan**. Network devices might react unexpectedly, for example network printers might print pages with illogical symbols and characters. It is important to use the **Exceptions List** and to disable the option **Scan systems marked as exceptions.** - **Report on self-configured subnets** — This is disabled by default. Enabling this feature reports all subnets with a netmask of /32 (or /128 in IPv6). With Layer 2 detections, you might see many erroneous 32-bit subnets appear in the subnet list. **Trellix** recommends that you enable this feature only when using DHCP detection and not Layer 2 detection. - **Sensor Scanning** — Select **Use active zero-configuration resolution** to enable the sensor to send multicast DNS requests and select **Use DNS queries for DNS name resolution** to resolve IP Addresses using DNS servers. > **Note** > > This setting is relevant for 5.x sensors only. [Results](/docs/rogue-system-detection-5-0-7-installation-guide#) After you have configured **Trellix RSD** server and policy settings, continue configuring **Trellix RSD**. ## Configuring server settings for Trellix RSD These server settings allow you to customize **Trellix RSD** to meet the specific needs of your organization. These settings control important behavior, including: - Whether a detected system is compliant (based on last agent communication) - The categories for system exceptions (systems that don't need an agent) - How detected system interfaces are matched - The list of OUIs used to identify vendor-specific NICs used by systems connecting to your network - How your Rogue System Sensors are configured ## **Edit** Detected System Compliance Edit the **Detected System Compliance** settings. These settings are user-configured. The settings have two important functions: - They specify the time frame that determines the state of detected systems (**Managed, Rogue, Exception, Inactive**). - They control the visual feedback of the **Trellix RSD** status monitors on the **Detected Systems** page. ### Task 1. Click Menu → Configuration → Server Settings, then in the Settings Categories list, click Detected System Compliance. 2. In the details pane, click Edit. 3. Edit the number of days to categorize Detected Systems as Managed or Inactive. 4. Edit the percentage levels for these options, so that the color codes represent your requirements: - Covered Subnets — Required coverage - System Compliance — Required compliance status - Sensor Health — Ratio of active to missing sensors 5. Use ePO Servers to configure additional Trellix ePO - On-prem servers whose detected systems are not considered rogue systems. 6. Click Save. > **Note** > > The number of days in **Rogue → Has Agent in Trellix ePO Database, but is older than__days** is controlled by the number of days set in the **Managed** field. ## **Edit** Detected System Exception Categories Configure and edit the categories to manage exception systems in your network. Exceptions are system that you know are unmanaged (don't have a **Trellix Agent** on them). --- ## Task 1. Click Menu → Configuration → Server Settings, then from the Settings Categories list, select Detected System Exception Categories and click Edit. 2. Add or subtract exception categories using + and -. > ![small blue note icon with pencil](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0012_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) > > **Note** > > Use the **Delete** and **Change** links to modify existing exceptions categories. 1. Specify a name and description for each exception category. For example, you might want to create a category named "Printers-US-NW" to contain all printers on your network in your company's Northwest regional offices. This way you can track these systems without receiving reports about them being rogue. 2. Click Save. ## Edit Detected System OUIs Edit the settings that specify the method and location used to update Detected System OUIs (Organizationally Unique Identifiers). Trellix RSD uses OUIs to provide details about the systems on your network. ## Task 1. Click Menu → Configuration → Server Settings, then from the server settings Categories list, select Detected System OUIs and click Edit. 2. Choose one of the following options to specify where to update your list of OUIs: - **URL** — Specifies the location of an OUI.txt file to be read. The Trellix ePO - On-prem server must have access to this location to pull the file directly from the path specified in the URL. - **Server location** — Specifies a location on this Trellix ePO - On-prem server where the OUI.txt file is located. - **File upload** — Type or browse to an OUI.txt file to upload to this Trellix ePO - On-prem server for processing, then click Update. ## Edit Rogue System Sensor settings Determine how sensors interact with each other and the **ePolicy Orchestrator** server. **Sensor** settings are user-configured and specify: - The amount of time that sensors are active - The maximum number of sensors active on each subnet --- - How long the server waits to hear from a sensor before categorizing it as missing ### Task 1. Click Menu → Configuration → Server Settings, then in the Settings Categories list, select Rogue System Sensor and click Edit. 2. Edit the Sensor Timeout field to set the maximum amount of time the server waits for a sensor to call in before specifying it as missing. 3. Edit the Sensors per Subnet field to set the maximum number of sensors active on each subnet, or select All sensors active. 4. Edit the Sensor Scanning section to specify systems you do not want to scan. This setting is useful for saving resources and lessening network traffic. - Add a list of **Sensor Scanning** MAC addresses and OUIs that the sensors do not actively probe, regardless of the configured policy. - For version 5.x sensors, you can add a list of IP addresses or subnet masks that sensors do not scan actively. These systems are not scanned regardless of the policy settings for the sensor. 5. Edit the Active Period field to set the maximum amount of time that passes before the server tells a sensor to become passive, or allows a new sensor to become active. 6. The Server Settings Revision ID field specifies the revision number of the setting. The ID is incremented every time the Server Settings are saved. 7. Click Save. > **Note** > > The **Active Period** setting doesn't set the communication times for the active and inactive sensors. Communication time is configured using communication policy settings for **Trellix RSD**. > **Note** > > This section applies only to version 5.x sensors. ### Results The new **Server Settings** take effect after the next agent-server communication interval. ## Trellix RSD permission sets Permission sets for **Trellix RSD** determine what information a user group can view, modify, or create for **Trellix RSD**. --- One or more permission sets can be assigned. By default, permission sets for administrators automatically include full access to all products and features. This table shows the **Trellix RSD** permission sets and their available rights. ### Trellix RSD [permissions](/docs/rogue-system-detection-5-0-7-installation-guide#) | Name | Possible Rights | | --- | --- | | Rogue System Detection | - Create and edit Rogue System information; manage sensors - No permissions - View Rogue System information | | Rogue System Sensor | - **Rogue System Detection : Policy** - No permissions - View settings - View and change settings - **Rogue System Detection : Tasks** - No permissions - View settings - View and change settings | This table shows the default **ePolicy Orchestrator** permission sets and their rights. ### Default Permission Sets and their Rights | Permission set | Rights | | --- | --- | | Executive Reviewer | No permissions | | Global Reviewer | - View sensor policy settings - View sensor task settings | | Group Admin | No permissions | | Group Reviewer | No permissions | # Install sensors After you configure **Trellix RSD** server settings, install the **Trellix RSD** sensors. Where you install the sensors and how many sensors you install affects how effective **Trellix RSD** is and can affect your network bandwidth. ### Before you begin Before you can install the **Trellix RSD** sensor on a system, the Rogue System Sensor software must be installed in the **Main Repository**. To add the sensor software, see *Check in engine, DAT and ExtraDAT update packages manually* in the *Trellix ePolicy Orchestrator - On-prem Product Guide*. This process is generic and also describes installing the **Trellix RSD** sensor. You can install **Trellix RSD** sensors on these types of systems: - **DNS or any system that is always connected to the subnet and monitoring traffic** — These systems are the best place to install **Trellix RSD** sensors because they are not often turned on or off and are seldom disconnected from the network. - **DHCP servers on multicast subnets** — DHCP servers constantly monitor multicast traffic and instantly detect when a new system connects to the subnet. - **All systems on a multicast subnet** — This allows you to configure **Active sensor election** in the **Trellix RSD** server settings. Once configured, all systems on a multicast subnet run an election algorithm to set some system sensors as active and the remainder as passive. The configuration settings control how often the software runs the algorithm. ## Install sensors on specific systems Create a deployment task that installs the Rogue System Sensor to the selected systems, then performs an immediate agent wake-up call. ### Task 1. Click Menu → Systems Section → System Tree → Systems and click any system. > **Tip** > > You can use the **Managed Systems for Subnet xxx.xxx.xxx.xxx** page to select systems. Click **Menu → Systems Section → Detected Systems**, click **Covered** or **Contains Rogues** in the Subnet Status monitor, then select any subnet and click **Actions → Detected Subnet → View Managed Systems**. > **Tip** > > You can also use the **Systems** page to select systems. Click **Menu → Systems Section → System Tree**. 1. Select the systems where you want to install sensors, then click **Actions → Rogue Sensor → Add or Remove Rogue Sensor**. - On the **Systems Details** page, you can install the sensor only from the system you are viewing. - On the **Managed Systems for Subnet xxx.xx.xx.x** page, select the systems where you want to install sensors. - On the **Systems** page, select a group in the **System Tree**, and select the systems where you want to install sensors. 3. In the **Action** pane, click OK. # Use queries and server tasks to install sensors Create a query that can run as a server task action, which installs sensors on managed systems. ### Task 1. Click Menu → Reporting → Queries & Reports, then click Actions → New. The Query Builder wizard opens. 2. On the Result Type page, select System Management as Feature Group, and Managed Systems as Result Types, then click Next. 3. From the Display Results As column on the Chart page, expand the List display and select Table, then click Next. 4. From the Available Columns pane on the Columns page, click the types of information you want your query to return, then click Next. 5. On the Filter page, click the properties you want to filter with and specify the values for each, then click Run. 6. Click Save and specify the name of your query and any notes, then click Save again. > **Tip** > > **Trellix** recommends using a product-specific prefix when naming your queries, to keep them organized and make them easier to find. For example, **RSD: QueryName**. 1. Click Menu → Automation → Server Tasks, then click Actions → New Task. The Client Task Builder wizard opens. 2. On the Description page, name and describe the task, specify the Schedule status, then click Next. 3. From the drop-down list on the Action page, select Run Query. 4. From the Query list, select the query you created, then from the Language drop-down list, select the language you want for the displayed results. 5. Select Add or Remove Rogue Sensor as the subaction to take on the results of the query, then click Next. 6. On the Schedule page, specify the schedule for the task, then click Next. 7. Review the summary of the task, then click Save. ## Results At every scheduled run, the query installs the latest sensor package to systems that meet the specified criteria. --- # Use a client task to install sensors Create a client task that installs the latest sensor package to systems on your network. ### Task 1. Click Menu → Policy → Client Task Catalog, select Rogue System Detection → Sensor Deployment as Client Task Types, then click Actions → New Task. The New Task dialog box appears. 2. Verify that Sensor Deployment is selected, then click OK. 3. Type a name for the task you are creating and add any notes. 4. Select Install, then click Save. Select **Run at every policy enforcement** if needed. 5. Click Menu → Systems Section → System Tree → Systems, then select the system on which you want to install sensors, then click Actions → Agent → Modify Tasks on a single system. 6. Click Actions → New Client Task Assignment. The Client Task Assignment Builder wizard appears. 7. On the Select Task page, select Product as Trellix RSD and Task Type as Sensor Deployment, then select the task you created for installing sensors. 8. Next to Tags, select the platforms to which you are deploying the packages: - Send this task to all computers - Send this task to only computers that have the following criteria — Use one of the edit links to configure the criteria. 9. Click Next. 10. On the Schedule page, select whether the schedule is enabled, and specify the schedule details, then click Next. 11. Review the summary, then click Save. ### Results At every scheduled run, the client task installs the latest sensor package to systems that meet the specified criteria. ## Configure a deployment task for groups of managed systems Configure a product deployment task to deploy products to groups of managed systems in the **System Tree**. ### Task 1. Open the New Task dialog box. 1. Select Menu → Policy → Client Task Catalog. 2. Under Client Task Types, select a product, then click New Task. 2. Select Product Deployment, then click OK. 3. Type a name for the task you are creating and add any notes. 4. Next to **Target platforms**, select the types of platform to use the deployment. 5. Next to **Products and components**, set the following: - Select a product from the first drop-down list. - Set the **Action** to **Install**, then select the **Language** of the package, and the **Branch**. - To specify command-line installation options, type the options in the **Command line** text field. See the product documentation for information on command-line options of the product you are installing. > **Note** > > You can click + or − to add or remove products and components from the list displayed. 1. **If you want to automatically update your security products, select Auto Update.** This also deploys the hotfixes and patches for your product automatically. > **Note** > > If you set your security product to update automatically, you cannot set the **Action** to **Remove**. 1. (Windows only) Next to **Options**, select whether you want to run this task for every policy process, then click **Save**. 2. Select **Menu → Systems Section → System Tree → Assigned Client Tasks**, then select the required group in the System Tree. 3. Select the **Preset** filter as **Product Deployment (Trellix Agent)**. Each assigned client task per selected category appears in the **details** pane. 4. Click **Actions → New Client Task Assignment**. 5. On the **Select Task** page, select **Product** as **Trellix Agent** and **Task Type** as **Product Deployment**, then select the task you created to deploy your product. 6. Next to **Tags**, select the platforms you are deploying the packages to, then click **Next**: - Send this task to all computers - Send this task to only computers that have the following criteria — Click **edit** next to the criteria to configure, select the tag group, select the tags to use in the criteria, then click **OK**. > **Tip** > > To limit the list to specific tags, type the tag name in the text box under **Tags**. 1. On the **Schedule** page, select whether the schedule is enabled, and specify the schedule details, then click **Next**. 2. Review the summary, then click **Save**. ## Results At every scheduled run, the deployment task installs the latest sensor package to systems that meet the specified criteria. --- # Trellix RSD command-line options You can run command-line options on 4.x sensors from the client system to solve issues or override the standard configuration. You can start the sensor manually from the command-line instead of starting it as a Windows service. You might want to do this if you are testing functionality, or to check the sensor version. The following table lists the runtime command-line options for the sensor. > Important > > Command-line options only apply to supported 4.x sensors. | **Switch** | **Description** | | --- | --- | | `--console` | Forces the sensor to run as a normal command-line executable; otherwise it must be run as an NT service. | | `--help` | Prints the Help screen and lists available command-line options | | `--install` | Registers the sensor with the Windows Service Control Manager. | | `--port` | Overrides the Server Port configuration setting in the registry that you specified during installation. This parameter takes effect only when running in command-line mode, which also requires the `--console` command-line switch. **Sample syntax:** `sensor.exe --port "8081" --console` | | `--server` "[server name]" or "[IP address]" | Overrides the Server Name configuration setting in the registry that you specified during installation. This parameter takes effect only when running in command-line mode, which also requires the `--console` command-line switch. **Sample syntax:** `sensor.exe --server "MyServerName" --console` | | `--uninstall` | Unregisters the sensor with the Windows Service Control Manager | | `--version` | Prints the version of the sensor and exits. | --- --- # Remove sensors Create a deployment task that removes the sensor from the selected systems, then performs an immediate agent wake-up call. ### Task 1. To select a system from the Systems page, click Menu → Systems Section → System Tree. 2. Select a group in the System Tree, then select the systems that you want to remove sensors from. > ![Light bulb icon indicating Tip](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0021_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Tip** > > Select systems from the **Managed Systems for Subnet xxx.xxx.xxx.xxx** page by clicking **Menu → Systems Section → Detected Systems**, clicking any **Covered** or **Contains Rogues** system in the **Subnet Status** monitor, then selecting any subnet and clicking **View Managed Systems** and selecting systems. > ![Light bulb icon indicating Tip](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/rogue-system-detection-5.0.7-installation-guide_page_0021_img_01.png?sv=2026-02-06&spr=https&st=2026-11-22T17%3A34%3A54Z&se=2026-11-22T18%3A34%3A54Z&sr=c&sp=r&sig=1Ot43vfP36aSPpaL%2Bl5C9PVlgHXT9LHF68M%2B%2F%2BAqJUg%3D) **Tip** > > You can also select systems from the **Systems Details** page by clicking **Menu → Systems Section → System Tree → Systems**, then clicking any system. You can remove the sensor from only the system you are viewing. 1. Click **Actions → Rogue Sensor → Remove Rogue Sensor**. 2. In the Action pane, click **OK**. ### Results The deployment task removes sensors from the selected systems.