--- title: "3. Configure fail-open switch parameters" slug: "3-configure-fail-open-switch-parameters-2" tags: ["Product Usage", "IPS 11.1.x"] updated: 2026-11-19T12:30:51Z published: 2026-11-19T12:30:51Z canonical: "docs.trellix.com/3-configure-fail-open-switch-parameters-2" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # 3. Configure fail-open switch parameters **Prerequisites:** To proceed with the setup, you will require: - One RJ-11 RS-232 cable - One RJ-45 cable Perform the following steps to configure the parameters of the fail-open switch. 1. Connect the applicable cables to the fail-open switch. 2. Connect the other end to a computer which runs a terminal emulation software such as HyperTerminal or PuTTY. 3. Launch the terminal emulation software, and set the communications parameters as shown below: - Baud rate: 9600 - Data bits: 8 - No parity - Stop bits: 1 - No flow control 4. Turn on the fail-open switch. The CLI banner and login prompt are displayed. 5. At the login prompt, type the username and password, and press **Enter**. **Username and password for both sets of fail-open switches** | For fail-open switches 6 thru 10 | | --- | | Username | `Trellix00` | | Password | `Trellix00` | The fail-open switch CLI prompt is displayed. 6. Use these commands for fail-open switch models 6 thru 10. **CLI commands for fail-open switch models 6 thru 10** | Command | Description | | --- | --- | | `set_ip xxx.xxx.xxx.xxx` | Configures fail-open switch IPv4 address. Reboot the fail-open switch for the new IPv4 address to take effect. | | `get_ip` | Displays fail-open switch IPv4 address. | | `set_netmask xxx.xxx.xxx.xxx` | Configures fail-open switch subnet mask. Reboot the fail-open switch for the new subnet mask to take effect. | | `get_netmask` | Displays fail-open switch subnet mask. | | `set_gateway xxx.xxx.xxx.xxx` | Configures default gateway IPv4 address. Reboot the fail-open switch for the new gateway IPv4 address to take effect. | | `get_gateway` | Displays default gateway address. | | `set_link <port> <on/off>` | Sets the port of a 1G Copper fail-open switch to auto-negotiate. For the `<port>` use `mon0`, `mon1`, `net0`, or `net1`. | | `get_link <port>` | Displays port status. For the `<port>` use `mon0`, `mon1`, `net0`, or `net1`. | | `set_link <port> off fd 100m` | Sets the port to 100 Mbps full-duplex. For the `<port>`, use the syntaxes specified above. | | `set_link <port> <enable/disable>_autoneg` | Sets the port of a 1G Fiber fail-open switch to auto-negotiate. For the `<port>` use `mon0`, `mon1`, `net0`, or `net1`. > [!NOTE] > Note > > 10G Fiber fail-open switches do not have such a command since auto-negotiate is enabled by default. | | `set_ssh_state <on/off>` | Enables or disables the SSH status on the fail-open switch. | | `get_ssh_state` | Displays the SSH status, which is enabled by default. | | `set_web_https_state <on/off>` | Enables or disables web access to the fail-open switch interface. | | `get_web_https_state` | Displays status of web access to the fail-open switch interface. | | `set_snmp_srv_ip` | Configures SNMP server IPv4 address. The SNMP server IPv4 address can also be set in the web interface. | | `get_snmp_srv_ip` | Displays the SNMP server IPv4 address. | | `set_trap <parameter> <on/off>` | Enables or disables the following SNMP traps: - **appl fail** – Application state change. - **bypass** – Bypass state change trap. - **mon link** – Monitoring port state change trap. - **net link** – Network port state change trap. - **error** – Error notification trap. - **update** – Update complete trap. | | `get_stat` | Displays the statistics of the fail-open switch. | | `get_params` | Displays fail-open switch parameters. | | `stop_all_sessions` | Stops all opened sessions |