--- title: "3. Configure fail-open switch parameters" slug: "3-configure-fail-open-switch-parameters" tags: ["Product Usage", "IPS 10.1.10"] updated: 2026-10-05T15:40:36Z published: 2026-10-05T15:40:36Z canonical: "docs.trellix.com/3-configure-fail-open-switch-parameters" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # 3. Configure fail-open switch parameters ## Before you begin To proceed with the setup, you will require: - One RJ-11 RS-232 cable - One RJ-45 cable Perform the following steps to configure the parameters of the fail-open switch. ## Task 1. Connect the applicable cables to the fail-open switch. 2. Connect the other end to a computer which runs a terminal emulation software such as HyperTerminal or PuTTY. 3. Launch the terminal emulation software, and set the communications parameters as shown below: - Baud rate: 9600 - Data bits: 8 - No parity - Stop bits: 1 - No flow control 4. Turn on the fail-open switch. The CLI banner and login prompt are displayed. 5. At the login prompt, type the username and password, and press **Enter**. | For fail-open switches 6 thru 10 | | --- | | Username | Trellix00 | | Password | Trellix00 | The fail-open switch CLI prompt is displayed. 6. Use these commands for fail-open switch models 6 thru 10. | Command | Description | | --- | --- | | set_ip xxx.xxx.xxx.xxx | Configures fail-open switch IPv4 address. Reboot the fail-open switch for the new IPv4 address to take effect. | | get_ip | Displays fail-open switch IPv4 address. | | set_netmask xxx.xxx.xxx.xxx | Configures fail-open switch subnet mask. Reboot the fail-open switch for the new subnet mask to take effect. | | get_netmask | Displays fail-open switch subnet mask. | | set_gateway xxx.xxx.xxx.xxx | Configures default gateway IPv4 address. Reboot the fail-open switch for the new gateway IPv4 address to take effect. | | get_gateway | Displays default gateway address. | | set_link <port> <on/off> | Sets the port of a 1G Copper fail-open switch to auto-negotiate. For the <port> use mon0, mon1, net0, or net1. | | get_link <port> | Displays port status. For the <port> use mon0, mon1, net0, or net1. | | set_link <port> off fd 100m | Sets the port to 100 Mbps full-duplex. For the <port>, use the syntaxes specified above. | | set_link <port> <enable/disable>_autoneg | Sets the port of a 1G Fiber fail-open switch to auto-negotiate. For the <port> use mon0, mon1, net0, or net1. > [!NOTE] > Note > > 10G Fiber fail-open switches do not have such a command since auto-negotiate is enabled by default. | | set_ssh_state <on/off> | Enables or disables the SSH status on the fail-open switch. | | get_ssh_state | Displays the SSH status, which is enabled by default. | | set_web_https_state <on/off> | Enables or disables web access to the fail-open switch interface. | | get_web_https_state | Displays status of web access to the fail-open switch interface. | | set_snmp_srv_ip | Configures SNMP server IPv4 address. The SNMP server IPv4 address can also be set in the web interface. | | get_snmp_srv_ip | Displays the SNMP server IPv4 address. | | set_trap <parameter> <on/off> | Enables or disables the following SNMP traps: - **appl fail** – Application state change. - **bypass** – Bypass state change trap. - **mon link** – Monitoring port state change trap. - **net link** – Network port state change trap. - **error** – Error notification trap. - **update** – Update complete trap. | | get_stat | Displays the statistics of the fail-open switch. | | get_params | Displays fail-open switch parameters. | | stop_all_sessions | Stops all opened sessions |