--- title: "Additional troubleshooting tips" slug: "additional-troubleshooting-tips-2" tags: ["Product Usage", "IPS 11.1.x"] updated: 2026-11-19T12:30:51Z published: 2026-11-19T12:30:51Z canonical: "docs.trellix.com/additional-troubleshooting-tips-2" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Additional troubleshooting tips ### Power settings - Press and hold the **PWR** button for at least 4 seconds to do a power cycle. - Press and hold the **PWR** button for at least 8 seconds to do a power shutdown. ### System reset - Press and hold the **RST** button for at least 1 second, to do a system reset. ### Force active fail-open bypass Kit module to Bypass or Tap mode 1. From the web interface, go to **Bypass** tab. 2. Click the **HB active mode** drop-down and select **off**. 3. Click the **Active Bypass** drop-down and select **bypass** or **tap**. 4. Click **Apply**. ![GUID-C37708E0-E612-436F-AC4F-F519DB3503D7-low.png](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-dd8b4b0b-2609-75cc-cb2f-eacbc3174709(7).png?sv=2026-02-06&spr=https&st=2026-11-20T13%3A36%3A55Z&se=2026-11-20T14%3A36%3A55Z&sr=c&sp=r&sig=KhXZvbjZPtBGu1vCgdnctNZy2RRwSY7UhegdU%2Bt9NxY%3D) ### CLI attributes After logging into the active fail-open bypass Kit CLI, depending on your access level, you will see one of the two login prompts: - `Info.m1s1.40g: AFO$` - `Ctrl.m1s1.40g: AFO$` The description of each parameter is given below: | Parameter | Definition | | --- | --- | | `Info` | Read-only mode | | `Ctrl` | Read/write mode | | `m1s1` | Module 1 - Segment 1 is being accessed. This is the default module at log on. > [!NOTE] > Note > > The value for the Segment is always `1`. | | `40g` | Type of active fail-open bypass kit | | `AFO` | Active fail-open bypass kit. This value will always remain the same | ### Disconnecting an active session - Type `exit` from the CLI. - From the web client, click **Logoff** in the upper right-hand corner. ### Changing the active fail-open bypass Kit module slot - From the CLI, type `set_seg <module_number> 1`. The parameter can have value of either 1, 2 or 3. ### List all get commands - Type `get help` from the CLI. The command displays the list of all supported get commands. ### List all set commands - Type `set help` from the CLI. The command displays the list of all supported set commands. ### Technical support information - Type `get_support_info` from the CLI. The command displays information needed for the Technical Support team to help resolve technical problems. ### Display sessions logged into the system - Type `display_sessions` from the CLI. ### CLI commands for troubleshooting The following CLI commands are applicable for 10G/40G Active Fail-Open Bypass Kit: | Command | Description | | --- | --- | | `display_sessions` | Displays details of the active CLI sessions | | `exit` | Ends current session. Once the sessions ends, the user who logged in after this session started will have read/write access. | | `get_dev_prop` | Displays device properties | | `get_dev_state` | Displays state of the device | | `get_seg` | Displays details of the module and segment that are being used | | `get_support_info <parameter> <number_of_lines>` | Displays information needed for the Technical Support team to help resolve technical problems. This command takes the following parameters: - `<parameter>` — Can be one of the following values: - `swd_log` — Displays lines of swdaemon log file - `kern_log` — Displays lines of kernel - `snmp_log` — Displays lines of snmp log file - `<number_of_lines>` — Number of lines to be displayed | | `power_off` | Shuts down the chassis | | `reboot` | Reboots the chassis > [!NOTE] > Note > > The chassis needs to be rebooted when a new module is inserted or if an old module is reseated. | | `reset_err` | Clears the **ALM** LED once error condition is corrected | | `set_default` | Resets parameters to factory default | | `set_psw <old_password> <new_password>` | Changes the current password | | `set_seg <module> <segment>` | Changes the module and the segment to a different active fail-open module in a different slot (either 1 or 2 or 3) > [!NOTE] > Note > > The value for the `<segment>` parameter will always be `1`. | | `set_session_exp_time <seconds>` | Sets the CLI and web sessions to timeout in seconds. The default value is `900` seconds. The maximum allowed value is `86400` seconds. | | `set_time` | Sets the time to user-specific time zone. Coordinated Universal Time (UTC) is the default time zone. | | `get help` | Displays all supported get commands | | `set help` | Displays all supported set commands |