Check your shipment

Each product ships with all the items needed to install the appliance on a network.

To verify that you received all the necessary items, verify that you have received the following:

Intelligent Sandbox Appliance
Accessories itemized on the Content Sheet
Set of tool-less slide rails
Front bezel with key
Country or region specific power cords

Intelligent Sandbox Appliance front and back panels

Figure 1. ATD-3000 and ATD-6000 front panel

Label	Description
1	System ID button with integrated indicator light
2	NMI button (recessed, tool required for use)
3	NIC 1 activity indicator light
4	ATD-3000: NIC 3 activity indicator light ATD-6000: Not used
5	System cold reset button
6	System status indicator light
7	Power button with integrated indicator light
8	Hard drive activity indicator light
9	ATD-3000: NIC 4 activity indicator light ATD-6000: Not used
10	NIC 2 activity indicator light

Figure 2. ATD-3000 Appliance back panel

Label	Description
1	Power supply module 1
2	Power supply module 2
3	Management port (NIC 1). This is the eth-0 interface. The `set appliance` and `set mgmtport` commands apply to this interface. For example, when you use the `set appliance ip` command, the corresponding IP address is assigned to this interface.
4	NIC 2. This is the eth-1 interface. This interface is disabled by default. To enable or disable this interface, use the `set intfport` command. For example, `set intfport 1 enable` To assign the IP details to this interface use `set intfport <eth 1, 2, or 3> ip <IPv4 address> <subnet mask>` For example, `set intfport 1 ip 10.10.10.10 255.255.255.0` You cannot assign the default gateway to this port. However, you can configure a route on this interface to route the traffic to the desired gateway. To configure a route, use `route add network <IPv4 subnet> netmask <netmask> gateway <IPv4 address> intfport 1` For example, `route add network 10.10.10.0 netmask 255.255.255.0 gateway 10.10.10.1 intfport 1`. This command routes all traffic from the 10.10.10.0 command to 10.10.10.1 through NIC 2 (eth-1).
5	NIC 3. This is the eth-2 interface. The note described for NIC 2 applies to this interface as well.
6	NIC 4. This is the eth-3 interface. The note described for NIC 2 applies to this interface as well.
7	Video connector
8	RJ45 serial-A port
9	USB ports
10	RMM4 NIC port
11	I/O module ports/connectors (not used)
12	Add-in adapter slots from riser card 1 and riser card 2

Figure 3. ATD-6000 Appliance back panel

Label	Description
1	USB ports
2	USB ports
3	Management port. This is the eth-0 interface. The `set appliance` and `set mgmtport` commands apply to this interface. For example, when you use the `set appliance ip` command, the corresponding IP address is assigned to this interface.
4	Additional I/O module ports/connectors. These are the eth-1, eth-2, and eth-3 interfaces respectively. These interfaces are disabled by default. To enable or disable an interface, use the `set intfport` command. For example, `set intfport 1 enable` to enable eth-1. To assign the IP details to an interface use `set intfport <eth 1, 2, or 3> ip <IPv4 address> <subnet mask>` For example, `set intfport 1 ip 10.10.10.10 255.255.255.0` You cannot assign the default gateway to this port. However, you can configure a route on this interface to route the traffic to the desired gateway. To configure a route, use `route add network <IPv4 subnet> netmask <netmask> gateway <IPv4 address> intfport 1` For example, `route add network 10.10.10.0 netmask 255.255.255.0 gateway 10.10.10.1 intfport 1`. This command routes all traffic from the 10.10.10.0 command to 10.10.10.1 through eth-1.
5	Video connector
6	NIC 1 (currently not used)
7	NIC 2 (currently not used)
8	RJ45 serial-A port
9	I/O module ports/connectors (not used)
10	Add-in adapter slots from riser card
11	RMM4 NIC port
12	Power supply module 2
13	Power supply module 1
14	Add-in adapter slots from riser card

Figure 4. ATD-3100, and ATD-6100 Appliance Front panel

Label	Description
1	System ID button with integrated indicator light
2	NMI button (recessed, tool required for use)
3	INTF2 activity indicator light
4	System status indicator light
5	Power button with integrated indicator light
6	Hard drive activity indicator light
7	System cold reset button
8	INTF3 activity indicator light

Figure 5. ATD-3100, and ATD-6100 Appliance back panel

Label	Interface port
1	Power supply module 1
2	Power supply module 2
3	Ethernet interface 2 (intf2)
4	Ethernet interface 3 (intf3)
5	VGA connector
6	Serial console interface
7	USB 3.0 ports
8	BMC port (RMM)
9	Ethernet interface 0 (ATD Management Interface)
10	Ethernet interface 1 (intf1)

Figure 6. ATD- 3200, ATD-6200 Appliance Front panel

Label	Description
1	System ID button with integrated indicator light
2	NMI button (recessed, tool required for use)
3	NIC 1 activity indicator light
4	System status indicator light
5	Power button with integrated indicator light
6	Hard drive activity indicator light
7	System cold reset button
8	NIC 2 activity indicator light

Figure 7. ATD- 3200, ATD-6200 Appliance Back panel - Configuration A

Figure 8. ATD- 3200, ATD-6200 Appliance Back panel - Configuration B

Label	Interface port
1	Power supply module 1
2	Power supply module 2
3	Ethernet interface 0 (ATD Management Interface)
4	Ethernet interface 1 (intf1)
5	VGA connector
6	Serial console interface
7	USB 3.0 ports (3)
8	BMC port (RMM)
9	Ethernet interface 3 (intf3)
10	Ethernet interface 2 (intf2)

If an item is missing or damaged, contact your supplier.