--- title: "Checking system health using the CLI" slug: "checking-system-health-using-the-cli-2" updated: 2026-08-25T21:18:33Z published: 2026-08-25T21:18:33Z canonical: "docs.trellix.com/checking-system-health-using-the-cli-2" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Checking system health using the CLI Use the CLI commands in this topic to view health and status information about Central Management System appliance components. This topic describes selected commands that return system, hardware status, DTI network, and interface information. For a full list of commands and details about their usage and parameters, see the *CLI Command Reference*. - Monitor, Operator, or Admin access - Admin access for the `show ipmi` command ### Note The examples in this section are from a Network Security appliance, but they are representative of Trellix appliances as well. To check appliance health: 1. Go to CLI enable mode: ``` hostname > enable ``` 2. Display detailed information about the system and the software running on it. ``` hostname # show version Product name:      Web MPS [licensed] Product model:     FireEyeNX9450 Product edition:   Classic Bandwidth:         2000 Mb Product release:   wMPS (wMPS) 7.7.0.433916 Build ID:          #433916 Build date:        2015-12-29 17:21:57 Build arch:        x86_64 Built by:          root@vta114 Version summary:   wmps wMPS (wMPS) 7.7.0.433916 #433916 2015-12-29 17:21:57 x86_64 build@vta108:FireEye (xxx) Content Version:   385.314 Appliance ID:      XXXXXXXXXXXX ``` ``` Product model:     FireEyeNX9450 Host ID:           XXXXXXXXXXX System serial num: XXXXXXXXXX System UUID:       XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX ``` ``` Uptime:            3d 6h 34m 34.205s CPU load averages: 0.36 / 0.40 / .38 Number of CPUs:    32 System memory:     9210 MB used / 119984 MB free / 129194 MB total Swap:              0 MB used / 65536 MB free / 65536 MB total ``` 3. Display the IPMI configuration: ``` hostname # show ipmi IPMI LAN Settings ---------------------------------------- Admin Shut Down         : no Shut Down               : no IP Address Source       : Static Address IP Address              : 192.168.42.27 Subnet Mask             : 0 Default Gateway IP      : 0 ``` ``` IPMI Firmware Installed ------------------------------- Firmware Version:         2.67 Device:                   1 IPMI Version:             2.0 ``` ``` IPMI Firmware Available For Update ----------------------------------- New Firmware Version:     2.67 New Firmware Filename:    FireEye_V267.bin Firmware Update Notice:   Firmware is up to date for this release IPMI Firmware Availability Notice is enabled ``` 4. Display overall system status: ``` hostname * show system health Overall system feature status: Good ``` 5. Display current status of system and available services: ``` hostname # show show health all ``` ``` Health Status: ``` ``` Last Updated at: : 2019-11-06T20:31:00 ``` ``` Service:        : System CPU/Memory/Disk IO Health ``` ``` Health Status:  : Healthy ``` ``` Details:        : Healthy ``` ``` Service:        : Global Cache ``` ``` Health Status:  : Healthy ``` ``` Details:        : Healthy ``` 6. Display information about the Dynamic Threat Intelligence (DTI) network: ``` hostname # show fenet status ``` ``` Dynamic Threat Intelligence Service: ``` ```    Update source   :    Enabled         : yes      Download        : DTIUser@cloud.fireeye.com      Upload          : DTIUser@up-cloud.fireeye.com    Mil             : DTIUser@mil-cloud.fireeye.com  HTTP Proxy: ``` ```     Address        :     Username       :     User-agent     : ``` ``` Request Session: ``` ```     Timeout        : 30       Retries        : 3     Speed Time     : 60     Max Time       : 14400     Rate Limit     :     Speed Limit    : 1   Dynamic Threat Intelligence Lockdown: ``` ``` Enabled             : no Locked              : no Lock After          : 5 failed attempts ``` ``` UPDATES                    Enabled   Notify  Scheduled   Last Updated At                    -------   ------  ---------   ------------------- Security contents: yes       no      every       2016/07/18 19:28:00 Stats contents:    yes               none        2016/07/18 15:55:00 ``` 7. Display status and traffic statistics for all interfaces: ``` hostname # show interfaces ``` ``` Interface ether1 status:   Comment:   Admin up:           yes   Link up:            yes   DHCP running:       no   IP address:         172.00.00.00     Netmask:            255.000.0.0   IPV6 enabled:       no   Speed:              1000Mb/s (auto)     Duplex:             full (auto)   Interface type:     ethernet   Interface ifindex:  12     Interface source:   physical   MTU:                1500   HW address:         00:25:90:D0:A3:76 ``` ```  RX bytes:        3114981133   TX bytes:       227921679   RX packets:       31934013     TX packets:     367951   RX mcast packets: 31564        TX discards:    0   RX discards:      296          TX errors:      0   RX errors:        1            TX overruns:    0   RX overruns:      0            TX carrier:     0   RX frame:         0            TX collisions:  0                                    TX queue len:   1000 ``` ``` Interface ether2 status:   Comment:   Admin up:           yes   Link up:            no   DHCP running:       no   IP address:               Netmask:   IPV6 enabled:       no               Speed:              UNKNOWN     Duplex:             UNKNOWN   Interface type:     ethernet   MTU:                1500   HW address:         00:25:90:D0:A3:77   RX bytes:           0              TX bytes:       0   RX packets:         0              TX packets:     0   RX mcast packets:   0              TX discards:    0   RX discards:        0              TX errors:      0   RX errors:          0              TX overruns:    0   RX overruns:        0              TX carrier:     0   RX frame:           0              TX collisions:  0                                        TX queue len:   0 ``` ``` Interface pether2 status:   Comment:   Admin up:           yes   Link up:            no   DHCP running:       no   IP address:   Netmask:   IPV6 enabled:       no   Speed:              UNKNOWN   Duplex:             UNKNOWN   Interface type:     ethernet   Interface ifindex:  9   Interface source:   physical   Bridge group:       ether2   MTU:                1500   HW address:         00:25:90:D0:A3:77     RX bytes:           0            TX bytes:       0   RX packets:         0            TX packets:     0   RX mcast packets:   0            TX discards:    0   RX discards:        0            TX errors:      0   RX errors:          0            TX overruns:    0   RX overruns:        0            TX carrier:     0   RX frame:           0            TX collisions:  0                                      TX queue len:   1000 ``` ``` Interface pether3 status:   Comment:   Admin up:           yes   Link up:            yes   DHCP running:       no   IP address:         127.0.0.10   Netmask:            255.255.255.0   IPV6 enabled:       no   Speed:              1000 MB/s (auto)   Duplex:             full (auto)   Interface type:     ethernet   Interface ifindex:  6   Interface source:   physical   MTU:                1500   HW address:         00:25:90:D0:A3:67     RX bytes:           31628620500   TX bytes:       0   RX packets:         46795         TX packets:     0   RX mcast packets:   367056        TX discards:    0   RX discards:        212322        TX errors:      0   RX errors:          0             TX overruns:    0   RX overruns:        0             TX carrier:     0   RX frame:           0             TX collisions:  0       TX queue len:   1000 ``` :