--- title: "Configure fail-open switch parameters" slug: "configure-fail-open-switch-parameters" tags: ["Hardware", "IPS 11.1.x"] updated: 2026-08-19T18:44:23Z published: 2026-09-17T07:33:47Z canonical: "docs.trellix.com/configure-fail-open-switch-parameters" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configure fail-open switch parameters You can configure various parameters on your fail-open switch. All configuration options, status, and statistics are accessible from the fail-open switch Command Line Interface (CLI). After you have configured basic network settings — IP address, gateway, and subnet mask — you will be able to access the fail-open switch through SSH. SSH is enabled on every fail-open switch by default and can be disabled through the CLI. > [!NOTE] > Note > > Your fail-open switch only supports IPv4 addresses. The steps below explain the configuration of parameters for your fail-open switch. **Steps:** 1. Connect an RJ-11 cable to the front of the module. 2. Connect the other end to a computer running a terminal emulation software, such as HyperTerminal or PuTTY. 3. Launch the terminal emulation software, and set the communications parameters as shown below: - Baud rate: 9600 > [!NOTE] > Note > > It is recommended not to alter the baud rate of the Management port. - Data bits: 8 - Parity: None - Stop bits: 1 - Flow control: None 4. Power up the fail-open switch. The CLI banner and login prompt appear. 5. At the login prompt, type `Trellix00` and press **Enter**. 6. At the password prompt, type `Trellix00` and press **Enter**. The fail-open switch CLI prompt appears. 7. Configure or modify parameters related to fail-open switch access and its ports using the commands listed. | Command | Description | | --- | --- | | `set_ip xxx.xxx.xxx.xxx` | Configures fail-open switch IPv4 address Reboot the fail-open switch for the new IPv4 address to take effect. | | `set_netmask xxx.xxx.xxx.xxx` | Configures fail-open switch subnet mask Reboot the fail-open switch for the new subnet mask to take effect. | | `set_gateway xxx.xxx.xxx.xxx` | Configures default gateway IPv4 address Reboot the fail-open switch for the new gateway IPv4 address to take effect. | | `set_link <port> <on/off>` | Sets the port of a 1G Copper fail-open switch to auto-negotiate For the `<port>` use `mon0`, `mon1`, `net0`, or `net1`. | | `set_link <port> off fd 100m` | Sets the port to 100 Mbps full-duplex For the `<port>`, use the syntaxes specified above. | | `set_link <port> <enable/disable>_autoneg` | Sets the port of a 1G Fiber fail-open switch to auto-negotiate For the `<port>`, use `mon0`, `mon1`, `net0`, or `net1`. > [!NOTE] > Note > > 10G Fiber fail-open switches do not have such a command since auto-negotiate is enabled by default. | 8. Configure or modify parameters for other settings of the fail-open switch using these commands. | Command | Description | | --- | --- | | `set_ssh_state <on/off>` | Enables or disables the SSH status on the fail-open switch | | `set_web_https_state <on/off>` | Enables or disables web access to the fail-open switch interface | | `set_snmp_srv_ip` | Configures SNMP server IPv4 address The SNMP server IPv4 address can also be set in the web interface. | | `set_trap <parameter> <on/off>` | Enables or disables the following SNMP traps: - **appl fail** – Application state change - **bypass** – Bypass state change trap - **mon link** – Monitoring port state change trap - **net link** – Network port state change trap - **error** – Error notification trap - **update** – Update complete trap | 9. View essential fail-open switch parameters using the commands listed. If your fail-open switch parameters have never been configured before, you will see factory settings. | Command | Description | | --- | --- | | `get_ip` | Displays fail-open switch IPv4 address | | `get_netmask` | Displays fail-open switch subnet mask | | `get_gateway` | Displays default gateway address | | `get_ssh_state` | Displays the SSH status, which is enabled by default | | `get_snmp_srv_ip` | Displays the SNMP server IPv4 address | | `get_params` | Displays fail-open switch parameters | | `get_web_https_state` | Displays the status of web access to the fail-open switch interface | | `get_link <port>` | Displays port status For the `<port>`, use `mon0`, `mon1`, `net0`, or `net1`. |