--- title: "Configure MDR for cloud" slug: "configure-mdr-for-cloud-12" tags: ["Product Usage"] updated: 2026-11-19T12:25:43Z published: 2026-11-19T12:25:43Z canonical: "docs.trellix.com/configure-mdr-for-cloud-12" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configure MDR for cloud First, you must configure MDR separately on both the Primary and Secondary Managers. To begin the configuration, follow the below steps: 1. In the Manager, select **Manager** → **** → **Setup** → **MDR**. > [!NOTE] > Note > > IPv6 addresses for MDR in public cloud environments are not supported. > [!NOTE] > Note > > The Manager supports a maximum of three IP addresses during MDR configuration. The Manager assumes that all the IP addresses are bound to the same hostname. **MDR Pair Creation page**![MDR Pair Creation page](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-ebf3451d-4618-155f-852f-b7fdbd7e39a5(10).png?sv=2026-02-06&spr=https&st=2026-11-20T14%3A12%3A40Z&se=2026-11-20T15%3A12%3A40Z&sr=c&sp=r&sig=Kp5Bdh6G8rE0JdL7yVa%2FwABPAu%2FlL%2FpsOjQ3ZlRw170%3D) 2. Fill in the following fields: **Option definitions** | Option | Definition | | --- | --- | | **Role of this Manager** | Select **Primary** to use this Manager as the active Manager, or **Secondary** to use this Manager as the standby. | | **Use Out-of-Band (OOB) Manager-to-Manager Communication?** | - **Yes** to use separate interfaces for Manager-Manager and Manager-Sensor communication - **No** to use the same interface for Manager-Manager and Manager-Sensor communication | | **Peer IP for Manager-to-Manager Communication** | This option appears if you selected the option **Yes** in **Use Out-of-Band (OOB) Manager-to-Manager Communication?** field. Enter the IP address of the Peer Manager that you want to use for Manager-Manager communication. > [!NOTE] > Note > > If you set **Use Out-of-Band (OOB) Manager-to-Manager Communication?** to **Yes** in the Primary Manager, set this option as **Yes** in your Secondary Manager as well. A mismatch in this option setting between the Primary and Secondary Manager pair will result in an MDR configuration failure. | | **Peer IP for Manager-to-Sensor Communication** | Enter the IP address of the peer Manager that is used for communication with the Sensor. | | **MDR Pair Shared Secret** | The same shared secret key must be entered on both Managers for MDR creation to be successful. Enter a minimum of eight characters and use no special characters. | | **Confirm MDR Pair Shared Secret** | Re-enter the same shared secret key. | | **Downtime Before Switchover** | Enter the downtime in minutes before the switch to the Secondary Manager occurs. Downtime before switchover should be between 1-10 minutes. This field is disabled if the **Role of this Manager** of Manager is set to Secondary. | 3. Click **Finish** to confirm your changes. > [!NOTE] > Note > > The Primary and Secondary Managers in an MDR pair use the GUI login credentials of the primary Manager only. > [!NOTE] > Note > > When you click **Finish** and your peer Manager's MDR settings are not yet configured, Trellix vIPS displays a warning to remind you to configure the peer Manager MDR settings. You can configure only **IPv4 address** for Manager-Sensor communication as given in the following scenarios: - If a Sensor is connected to the Manager over an IPv4 network, or you want to add a Sensor from the IPv4 network to the Manager, you need to enter the **IPv4 address** of the peer Manager. - When **Use Out-of-Band (OOB) Manager-to-Manager Communication** is set to **No**, **Peer IP for Manager-to-Sensor Communication** is used for both Manager-Manager and Manager-Sensor communication. - When **Use Out-of-Band (OOB) Manager-to-Manager Communication** is set to **Yes**, **Peer IP for Manager-to-Sensor Communication** is used only for Manager-Sensor communication. > [!WARNING] > Important > > You need to use the **Peer IP for Manager-to-Sensor Communication** while establishing trust between the Sensor and Manager. Ensure that your peer Manager is configured to use the same IP address as selected from the **Dedicated Interface** list during the Peer Manager installation. If misconfigured, Trellix vIPS generates an error message to prompt you to enter the correct IP address.