--- title: "Configure network settings for Trellix IVX" slug: "configure-network-settings-for-trellix-ivx" tags: ["Intelligent Sandbox", "Migration"] updated: 2026-09-11T12:36:23Z published: 2026-09-11T12:36:23Z canonical: "docs.trellix.com/configure-network-settings-for-trellix-ivx" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configure network settings for Trellix IVX After the migration completes, log in to the appliance and change the default administrator credentials before performing the initial network configuration. 1. Log in with the default username and password (admin/admin). 2. Run the enable command, followed by the configure terminal command, to enter configuration mode. ``` hostname > enable hostname # configure terminal ``` 3. Change the default admin user password using the following command: ``` hostname (config) # username admin password ``` 4. Log in with the new admin credentials and accept the End User License Agreement (EULA). 5. Configure the following network settings in CLI console: | Steps | Response | | --- | --- | | Hostname? | Enter the hostname for the appliance. | | Admin password? | Enter a new administrator password. The new password must be at least 8 characters. You can skip this step if you have already changed your administrator password. | | Enable remote access for ‘admin’ user? | Enter **yes** to enable the administrator to log in to the appliance remotely. Enter **no** to disable remote access. | | Use DHCP on ether1 interface? | Enter **yes** to use Dynamic Host Configuration Protocol (DHCP) to configure the appliance IP address and other network parameters. Enter **no** to manually configure your IP address and network settings. If you enter **yes**, proceed to the **Default gateway** step. | | Use zeroconf on ether1 interface? | Enter **yes** to use zero-configuration (zeroconf) networking on the ether1 interface. ### Note Do not use zeroconf on the primary interface. | | Primary IPv4 address and masklen? | Enter the IP address in A.B.C.D format and the network mask for the management interface, for example, 10.10.1.1 /24 or 10.10.1.1 255.255.255.0. | | Default gateway? | Enter the gateway IP address for the management interface. | | Primary DNS server? | Enter the IP address of the DNS server. | | Domain name? | Enter the domain for the management interface. | | Enable fenet service? | Enter **yes** to enable FireEye Network (fenet) services. If you enter **no**, proceed to the **Enable NTP** step. | | Enable fenet license update service? | Enter **yes** to enable the license update service for fenet. If you enter **no**, proceed to the **Enable NTP** step. | | Sync appliance time with fenet? | Enter **yes** to synchronize the appliance time with fenet service. If you enter no, the appliance will not synchronize with fenet. | | Enable NTP? | Enter **yes** to use the default Network Time Protocol (NTP) servers to enable automatic time synchronization. Enter **no** to manually set the time and date on the appliance. (This step is skipped if you enter **yes** in the "**Sync appliance time with fenet?**" step) | | Enable IPv6 on ether1 management interface | Enter **yes** to enable the IPv6 protocol in addition to IPv4. | | Product license key | Once the system retrieves an IP address and the fenet services are enabled, the product license key is automatically applied. ### Note If the license is not configured in the network, contact Trellix Support. | | Security content updates key | Once the system retrieves an IP address and the fenet services are enabled, the security content license key is automatically applied. ### Note If the license is not configured in the network, contact Trellix Support. | | Submission: Interface | Press **Enter** to use ether1 as the submission interface. | | Cluster: Interface | Press **Enter** to use ether1 as the cluster interface. Otherwise, enter the name of the other interface such as ether2, ether3 or ether4. | | Send a request to be managed by CMS | Enter **yes** only if the appliance is managed by Trellix Central Management System (CMS). | ### Verify IVX license status Systems with internet access and fenet services enabled in the firewall automatically retrieve the license. - Verify whether the system is licensed or not using the **show version** command. ``` hostname > show version ``` - View the list of systems with licenses installed: ``` hostname > enable hostname # configure terminal hostname (config) # show licenses ``` - Verify whether the system retrieves the following licenses: - FireEye Appliance - FireEye Support - Content updates ![IVX_FE_licenses.png](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-f4069d52-bf09-0457-7173-7944728fdd48.png?sv=2026-02-06&spr=https&st=2026-11-22T14%3A44%3A44Z&se=2026-11-22T15%3A44%3A44Z&sr=c&sp=r&sig=gQuF6L2psgCvt7gEvJnfGz2wp9HS2ZQW7Gh540vvKnQ%3D) Execute the following command if you are unable to retrieve any of the three licenses. If you still encounter issues, contact Trellix Support. ``` hostname > enable hostname # configure terminal hostname (config) # configuration jump-start ``` ### Note If you are operating on an air-gap network, you must contact Trellix Support or Professional Services to retrieve the license keys for your appliances. :