--- title: "Configure SNMP setting" slug: "configure-snmp-setting" updated: 2026-09-08T19:56:44Z published: 2026-09-08T19:56:44Z canonical: "docs.trellix.com/configure-snmp-setting" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configure SNMP setting Intelligent Sandbox supports SNMP version 2c and version 3. To enable users to manage Intelligent Sandbox resources efficiently, the SNMP service obtains integral values through SNMP traps. Intelligent Sandbox supports the 1.3.6.1.4.1.8962.4.1.1 OID (object identifier). Intelligent Sandbox also provide SNMP support to standard .1.3.6.1.2.1.1 OID subtree, which includes sysName, sysDecr, sysContact, and sysLocation fields to identify the resource. The sysName value is taken from Intelligent Sandbox hostname configured by "set appliance name " command execution. The qualified attributes for SNMP traps include: - Hard disk utilization - CPU utilization - Memory utilization - ATD services such as system health, load balancers, and malware interface status. - Other statuses such as DXL channel, TAXII, and sensor. 1. Log on to Intelligent Sandbox web interface. 2. Click Manage → TIS Configuration → SNMP. 3. Select **Allow SNMP Monitoring**, to configure SNMP. Intelligent Sandbox allows you to configure the following SNMP versions: - **SNMPv2c** - **SNMPv3** 4. If you want to set up **SNMPv2c**, then select **SNMPv2c**, and enter the **Community String** for your Intelligent Sandbox appliance. The default **Community String** is **`atdpublic`**. 5. If you want to set up **SNMPv3**, then select **SNMPv3**, then do the following: 1. Enter the username, then select the appropriate **Security Level** and **Authentication type**. 2. Enter the **Authentication Password** and **Privacy Password**. 6. In the SNMP System Information section, enter these fields: - **Description** – The field value is saved as sysDescr. - **Contact** – The field value is saved as sysContact. - **Location** – The field value is saved as sysLocation. ### Note For the Load Balancer configuration, these fields must be defined on each node individually. 7. To configure SNMP Traps, select **Send SNMP Traps**, then do the following: ### Note **CPU Utilization** field appearing in the **SNMP Setting** page is different from **CPU Load** featuring under **System Health** in the **Dashboard** tab. 1. Enter the **Destination IP** and **Port Number**. 2. Then choose the SNMP traps that you'd want to collect. | Category | Option | Definition | | --- | --- | --- | | **Device** | **Hard Disk Utilization** | Trap is generated when: - Var disk partition utilization exceeds the configured threshold limit. - Data disk partition utilization exceeds the configured threshold limit. | | **CPU Utilization** | Traps are sent when the overall CPU utilization of the device exceeds the configured threshold value. | | **Memory Utilization** | Traps are sent when the overall Memory utilization of the device exceeds the configured threshold value. | | **TIS Services** | **System Health** | The follows trap value is sent: - **0** – If System Health is Bad. - **1** – if System Health is Good. ### Tip System Health is flagged as Bad when any one of the critical services is down. | | **Backup Scheduler** | The follows trap value is sent: - **0** – if Backup file creation fails or FTP of backup file to server fails. - **1** – if backup scheduler runs successfully. | | **Load Balancer** | The follows trap value is sent: - **0** – device is in standalone mode - **1** – LB status is DOWN - **2** – LB status is UP - **3** – Nodes status is SW VERSION MISMATCH - **4** – Primary Node LB services are not UP - **5** – SCP failed - **6** – VM Creation failed - **7** – Invalid status | | **Email Connector** | The follows trap value is sent: - **0** – Email Connector status is DISABLED - **1** – Email Connector status is Enabled and Email Connector health is GOOD - **2** – Email Connector health is DEGRADED - **3** – Email Connector health is OVERLOADED | | **Email Gateway Wait time** | Trap is sent with value **1** when the Wait Time for McAfee Email Gateway exceeds the configured threshold value set in **Global Settings**. | | **Malware Interface Status** | The follows trap value is sent: - **0** – malware interface status is DOWN. - **1** – malware interface status is UP. | | **License Status** | The follows trap value is sent from Virtual Intelligent Sandbox: - **1** – License is VALID - **2** – License is INVALID - **3** – License is EXPIRED | | **Malware DNS Status** | The following trap value is sent: - **0** – Malware DNS status is DOWN. - **1** – Malware DNS status is UP. | | **Point Products** | **DXL Status** | The follows trap value is sent: - **0** – Last attempt to send TIE report failed. - **1** – Last attempt to send TIE report was successful. | | **TAXII Status** | The follows trap value is sent: - **0** – Last attempt to send TAXII report failed. - **1** – Last attempt to send TAXII report was successful. - **2** – STIX report sent is not yet received. | | **Sensor Status** | The follows trap value is sent for NSP Sensor status: - **0** – Sensor status is INACTIVE. - **1** – Sensor status is ACTIVE. - **2** – Sensor status is NOT CONNECTED. | 8. Click **Submit**. ### What to do next - Ensure that you download the latest management information base (MIB) file using from MIB Download link on the SNMP Configuration page. Then upload the file to your SNMP MIB browser. - To retrieve the attribute numeric values, enter the **`snmpget`** command in the command prompt or any MIB browser. :