---
title: "Configure the Manager on MLOS"
slug: "configure-the-manager-on-mlos"
tags: ["Install and Get Started", "IPS 10.1.10"]
updated: 2026-09-23T09:38:30Z
published: 2026-09-23T09:38:30Z
canonical: "docs.trellix.com/configure-the-manager-on-mlos"
---
> ## Documentation Index
> Fetch the complete documentation index at: https://docs.trellix.com/llms.txt
> Use this file to discover all available pages before exploring further.
# Configure the Manager on MLOS
Login to the Manager/Central Manager virtual machine using a console client and configure the network settings as shown here.
## Task
1. Log in to the Manager shell using the following credentials:
- Username:
admin
- Password:
MLOSnsmApp
> [!NOTE]
> Note
>
> SSH connection to the Linux based Manager Appliance is not supported by Putty application. Trellix recommends you to use Tera Term application for remotely accessing the Manager Appliance using SSH.
> [!NOTE]
> Note
>
> Trellix **strongly recommends** that you change the password immediately. The new password must be at least 8 characters in length and must contain a combination of numbers, characters, and special characters. For more information on the password control, see section Configure password complexity settings in Trellix Intrusion Prevention System Product Guide.
2. To update network parameters, execute the
set network configuration command.
Syntax:
set network configuration
> [!NOTE]
> Note
>
> The set network configuration command overwrites the pre-existing network configuration in the Manager server.
> [!NOTE]
> Note
>
> You can only configure IPv4 addresses in the MLOS Manager Appliance box.
> [!NOTE]
> Note
>
> You can terminate the network configuration by executing the quit command.
On executing the
set network configuration command, follow the steps below:
1. Select the type of NIC configuration:
```
Please select one of the below option:
1 -> Configure Single NIC
2 -> Configure Both the NIC's
Input 1 or 2 based on you selection :
```
Type
1 to configure NIC 1 or NIC 2, or
2 to configure both NIC 1 and NIC 2.
2. Select the NIC to be configured with public IP address for management purpose:
```
Enter the NIC you want to configure with public network ip:
1 -> eth0 [NIC 1]
2 -> eth1 [NIC 2]
Input 1 or 2 based on your selection :
```
Type
1 to select NIC 1 or
2 to select NIC 2 based on your network cable connection for public IP address.
> [!NOTE]
> Important
>
> The NIC 1 and NIC 2 ports are interchangeable:
>
> - When configuring a single NIC, you can assign the public IP address to NIC 1 or NIC 2.
> - When configuring dual NIC, you can assign a public IP address to NIC 1 and a private IP address to NIC 2 or vice-versa.
> [!NOTE]
> Note
>
> The Manager Appliance can have only one public and one private IP address.
3. Enter the Manager Appliance network parameters as shown below:
| Parameters | Description |
| --- | --- |
| DOMAIN NAME | Enter the domain name for the Manager server. |
| HOSTNAME | Enter the hostname to be assigned to the Manager server. |
| **Configuring the eth"x" with public IP** |
| IP ADDRESS | Enter the public IP address to be assigned to the Manager server. |
| NETMASK | Enter the subnet mask for the Manager server. |
| GATEWAY | Enter the gateway address for the Manager server. |
| DNS1 | Enter the primary DNS server IP address. |
| Do you want to enter DNS2 <y/n> | Type y, if you want to configure a secondary DNS server IP address, else type n. |
| DNS2 | (Optional) Enter the secondary DNS server IP address. |
| **Configuring the eth"y" with private IP** (Applicable only when 2 -> Configure Both the NIC's option is selected in step a). |
| IP ADDRESS | Enter the private IP address to be assigned to the Manager server. |
> [!NOTE]
> Note
>
> The Manager server will reboot automatically after completing the network configuration.
> [!NOTE]
> Note
>
> Make a note of the MAC address displayed after successful execution of set network configuration command.
## Results
You can now use the public IP address to access the UI from a remote location using a client machine and manage the Manager Appliance from a remote location using SSH . If required, unplug the monitor, keyboard, and mouse.