--- title: "Configuring and activating an accessible DTI server address using the CLI" slug: "configuring-and-activating-an-accessible-dti-server-address-using-the-cli" tags: ["File Protect (FX)", "Product Usage"] updated: 2026-10-01T15:21:12Z published: 2026-10-01T15:21:12Z canonical: "docs.trellix.com/configuring-and-activating-an-accessible-dti-server-address-using-the-cli" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring and activating an accessible DTI server address using the CLI Use the CLI commands in this section to configure a custom DTI address, and activate it as an accessible DTI server address for managed File Protect appliances using the dual-port address type. ### Important Do not use this procedure for any reason other than the scenario described in [Changing the address type for DTI network service requests](/network-and-platform/docs/changing-the-address-type-for-dti-network-service-requests-1) . You must enter the commands in the order shown. ### Note This configuration must be performed on each managed appliance. You can repeat the procedure on each appliance, or use appliance group functionality to configure the accessible address on multiple appliances at the same time. Only one custom DTI address can be configured. To configure the custom address: 1. Log in to the File Protect CLI. 2. Go to CLI configuration mode: ```plaintext appl-hostname > enable appl-hostname # configure terminal ``` 3. Configure the accessible address for the DTI` source`: 1. Prevent the local address from overriding the accessible address: ```plaintext appl-hostname (config) # no fenet dti source override enable ``` 2. Configure the IP address and port: ```plaintext appl-hostname (config) # fenet dti source type address [port ] ``` where` name `is a name of your choice and` ipAddress ` is the NAT IPv4 or IPv6 address. The` port `parameter is optional and defaults to 443 if it is not specified. 3. Specify the DTI server user and password: ```plaintext appl-hostname (config) # fenet dti source type username password ``` 4. Set` CUSTOM `as the default DTI source type: ```plaintext appl-hostname (config) # fenet dti source default ``` 4. Configure the accessible address for the DTI` upload destination`: 1. Prevent the local address from overriding the accessible address: ```plaintext appl-hostname (config) # no fenet dti upload destination override enable ``` 2. Configure the address and port: ```plaintext appl-hostname (config) # fenet dti upload destination type address [port ] ``` where` name `is a name of your choice and` ipAddress ` is the NAT gateway IPv4 or IPv6 address. The` port `parameter is optional and defaults to 443 if it is not specified. 3. Specify the DTI server user and password: ```plaintext appl-hostname (config) # fenet dti upload destination type username password ``` 4. Set` CUSTOM `as the default DTI upload destination type: ```plaintext appl-hostname (config) # fenet dti upload destination default ``` 5. Configure the accessible address for the` enrollment`,` faude`,` mil`,` helix`, or` virtual `service: 1. Prevent the local address from overriding the accessible address: ```plaintext appl-hostname (config) # no fenet dti service override enable ``` 2. Configure the address and port: ```plaintext appl-hostname (config) # fenet dti service type address [port ] ``` where` name `is a name of your choice and ` ipAddress ` is the virtual NAT IPv4 address or IPv6 address. The` port `parameter is optional and defaults to 443 if it is not specified. 3. Specify the DTI server user and password: ```plaintext appl-hostname (config) # fenet dti service type username password ``` 4. Set` CUSTOM `as the default DTI service type: ```plaintext appl-hostname (config) # fenet dti mil service default ``` 6. Verify the configuration: ```plaintext appl-hostname (config) # show fenet ``` 7. Save your changes. ```plaintext appl-hostname (config) # write memory ``` ### Deleting the custom DTI source You can delete the custom DTI source, which removes it from the list of available options. ### Note You cannot delete the custom DTI source if it is an active DTI source for managed appliances. To delete the custom DTI source: 1. Go to CLI configuration mode: ```plaintext appl-hostname > enable appl-hostname # configure terminal ``` 2. Delete the custom DTI source: ```plaintext appl-hostname (config) # no fenet dti source type ``` 3. Verify your changes: ```plaintext appl-hostname (config) # show fenet dti configuration ``` 4. Save your changes: ```plaintext appl-hostname (config) # write memory ``` ### Example The following example configures a custom address named "CUSTOM" and prevents the Central Management System appliance from overriding it with the Central Management System local address. ```plaintext appl-hostname (config) # no fenet dti source override enable appl-hostname (config) # fenet dti source type CUSTOM address 10.3.3.5 port 2000 appl-hostname (config) # fenet dti source type CUSTOM username user8 password 123ABCXYZ appl-hostname (config) # fenet dti source default CUSTOM appl-hostname (config) # no fenet dti upload destination override enable appl-hostname (config) # fenet dti upload destination type CUSTOM address 3.3.3.5 port 2000 appl-hostname (config) # fenet dti upload destination type CUSTOM username user8 password 123ABCXYZ appl-hostname (config) # fenet dti upload destination default CUSTOM ... appl-hostname (config) # show fenet DTI CLIENT CONFIGURATION:  Download source    :  CUSTOM (user8@10.3.3.5)  Upload destination :  CUSTOM (user8@10.3.3.5)  Update channel     :  CUSTOM (user8@10.3.3.5)    Http proxy         :  None  Connect timeout    :  30 (max tries: 3)  Speed Time         :  60  Max Time           :  14400  Rate Limit         :  None  Lockdown enabled   :  No  SSL minimum version:  tls1  SSL cipher list    :  compatible ``` :