--- title: "Configuring initial settings using the serial console port" slug: "configuring-initial-settings-using-the-serial-console-port-5" tags: ["Network Security (NX)"] updated: 2026-11-18T20:58:42Z published: 2026-11-18T20:58:42Z canonical: "docs.trellix.com/configuring-initial-settings-using-the-serial-console-port-5" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring initial settings using the serial console port If you are not using a terminal server, you need to be physically near the Network Security appliance to use the serial port. The serial port is on the back of the appliance. See your *Hardware Administration Guide* to view the port location. The serial port uses the following settings: - Baud rate: 115200 - Data bits: 8 - Stop bits: 1 - Parity: None - Flow control: XON/XOFF > [!NOTE] > Note > > If the appliance stops responding on startup without displaying an error message, the serial port or the connection may be faulty. If this occurs, do the following: > > 1. Press and hold the power button on the front of the appliance for a few seconds until the appliance powers off. > 2. Unplug all power cables from the server and wait for about 5 minutes to ensure shutdown is complete. > 3. Connect a different serial cable. > 4. Plug in the power cables. > 5. If the server does not automatically restart, press the power button. Configure initial settings as described in the following topics: - [Using a Windows or Mac Laptop](/network-and-platform/docs/configuring-initial-settings-using-the-serial-console-port-5#using-a-windows-or-mac-laptop) - [Using a Linux System](/network-and-platform/docs/configuring-initial-settings-using-the-serial-console-port-5#using-a-linux-system) - [Using a Terminal Server](/network-and-platform/docs/configuring-initial-settings-using-the-serial-console-port-5#using-a-terminal-server) #### Using a Windows or Mac laptop Use the procedure in this section to configure initial settings from a Windows or Mac laptop. To configure initial settings from a Windows or Mac laptop: 1. Establish a connection with the serial console as described in [PC or Mac](/network-and-platform/docs/pc-or-mac-2). 2. When prompted, enter the default username (`admin`) and password (`admin`) for the administrator. 3. You are asked to accept the End User License Agreement (EULA). Enter `y` to accept the terms of the agreement. 4. Enter `y` when you are prompted to use the Configuration Wizard for initial configuration. Then respond to the prompts as described in [Configuration wizard steps](/network-and-platform/docs/configuration-wizard-steps-3). 5. After you answer the questions, the wizard summarizes your answers. To change an answer, enter the step number. Press Enter to save changes. #### Using a Linux system Use the procedure in this section to configure initial settings from a Linux system. To configure initial settings from a Linux system: 1. Establish a connection with the serial console as described in [Linux](/network-and-platform/docs/linux-2). 2. When prompted, enter the default username (`admin`) and password (`admin`) for the administrator. 3. You are asked to accept the End User License Agreement (EULA). Enter `y` to accept the terms of the agreement. 4. Enter `y` when you are prompted to use the Configuration Wizard for initial configuration. Then respond to the prompts as described in [Configuration Wizard Steps](/network-and-platform/docs/configuration-wizard-steps-3) . 5. After you answer the questions, the wizard summarizes your answers. To change an answer, enter the step number. Press Enter to save changes. #### Using a terminal server Use the procedure in this section to configure initial settings from a terminal server. To configure initial settings from a terminal server: 1. Establish a connection with the serial console as described in [Terminal server](/network-and-platform/docs/terminal-server-2). 2. When prompted, enter the default username (`admin`) and password (`admin`) for the administrator. 3. You are asked to accept the End User License Agreement (EULA). Enter `y` to accept the terms of the agreement. 4. Enter `y` when you are prompted to use the Configuration Wizard for initial configuration. Then respond to the prompts as described in [Configuration Wizard Steps](/network-and-platform/docs/configuration-wizard-steps-3) . 5. After you answer the questions, the wizard summarizes your answers. To change an answer, enter the step number. Press Enter to save changes.