--- title: "Configuring inline multi-proxy mode using the CLI" slug: "configuring-inline-multi-proxy-mode-using-the-cli" tags: ["Network Security (NX)"] updated: 2026-08-24T22:01:11Z published: 2026-08-24T22:01:11Z canonical: "docs.trellix.com/configuring-inline-multi-proxy-mode-using-the-cli" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring inline multi-proxy mode using the CLI Inline multi-proxy deployment requires two network port pairs. This can be accomplished using a Network Security appliance with two port pairs, or one port pair from each of two Network Security appliances. Use the CLI commands in the following topics to configure inline blocking mode for an inline deployment with multiple proxies. > [!NOTE] > Note > > Inline deployment has three operational modes. It is highly recommended that you set your appliance to inline blocking mode. > > > [!NOTE] > > Note > > > > If you set the operational mode to block traffic, input a fail-safe setting (**block open** or **block close**). > > - **block**—Blocks malicious traffic (recommended). > > - **open**—In case of failure, all traffic passes through (recommended). > - **close**—In case of failure, all traffic is blocked. (Use this setting only if the device is actively monitored). > - **monitor**—Monitors the traffic and generates alerts on malicious events. > - **bypass**—Forced bypass wherein the Network Security appliance neither blocks nor analyzes traffic. > > > [!NOTE] > > Note > > > > Starting with version 7.1.0, Network Security appliances bypass packets larger than 1650 bytes rather than dropping them. > [!NOTE] > Note > > The following policy types are supported: > > - **mixed**—Applies both local and global policies, and the local policy overrides the global policy (recommended). > - **global**—Applies Trellix-defined global policy to the specified interface. > - **local**—Applies user-defined local policy to the specified interface. > - **none**—Does not apply any policy. No policy is used. For details about inline deployment with multiple proxy servers, refer to the *Hardware Administration Guide* for your appliance model. Prerequisites - Operator or Admin access ##### Configuring inline multi-proxy mode with one Network Security appliance Use the CLI commands in this topic to configure Network Security appliances with multiple network port pairs. Interface A connects the LAN-facing switch or router (A1) to the proxy server (A2). Interface B connects the LAN-facing switch or router (B1) to the Internet-facing switch or router (B2). Additional Network Security appliances connect to one or more additional proxy servers. To configure interface A and interface B on NX Appliance1: 1. Enable the CLI configuration mode: ``` hostname1 > enable ``` ``` hostname1 # configure terminal ``` ``` hostname1 (config) # policymgr interface A re-configure ``` 2. Configure pair A (interfaces A1 and A2) and pair B (B1 and B2) in inline block mode: ``` hostname1 (config) # policymgr interface A op-mode block fail-safe open policy-type mixed ``` ``` hostname1 (config) # policymgr interface B op-mode block fail-safe open policy-type mixed ``` ``` hostname1 (config) # policymgr interface B re-configure ``` 3. Save your changes: ``` hostname1 (config) # write memory ``` 4. Configure interface A2 to allow incoming traffic from the proxy server to pass through unblocked: ``` Proxy_IP_address ``` 5. Save your changes: ``` hostname1 (config) # write memory ``` To configure NX Appliance2 - NX Appliance *n* to connect to one or more proxy servers: 1. Enable the CLI configuration mode: `hostname > enable` `hostname # configure terminal` 2. Configure pair A (interfaces A1 and A2) in inline blocking mode on each NX Appliance2–NX Appliance*n*: `hostname (config) # policymgr interface A op-mode block fail-safe open policy-type mixed` `hostname (config) # policymgr interface A re-configure` 3. Save your changes: `hostname (config) # write memory` 4. Configure interface A2 to allow incoming traffic from the proxy server to pass through unblocked on each appliance connected to a proxy server: `hostname (config) # policymgr network host <Proxy_IP_address> interface A2 allow` where `Proxy_IP_address` is the IP address of the server. 5. Save your changes: `hostname (config) # write memory` 6. Check your configuration: ``` hostname (config) # show policymgr interfaces ``` ``` Policy enabled: yes ``` ``` Interface A  Active   : yes  op mode  : block (blocking)  fail-safe: open  policy   : mixed  tolerance: 1  Ports    : pether3  pether4 Interface B  Active   : yes  op mode  : block (blocking)  fail-safe: open  policy   : mixed  tolerance: 1  Ports    : pether5  pether6 ``` ##### Configuring inline multi-proxy mode with two Network Security appliances Use the CLI commands in this topic to configure deployment with two Network Security appliances with one network port pair each. NX Appliance1 is inline between a LAN-facing switch or router and an Internet-facing switch or router. NX Appliance2—NX Appliance *n* connect to multiple proxy servers offline. To configure NX Appliance1: 1. Enable the CLI configuration mode: ``` hostname1 > enable ``` ``` hostname1 # configure terminal ``` 2. Configure pair A (interfaces A1 and A2) in inline block mode: ``` hostname1 (config) # policymgr interface A op-mode block fail-safe open policy-type mixed ``` ``` hostname1 (config) # policymgr interface A re-configure ``` 3. Save your changes: ``` hostname1 (config) # write memory ``` 4. Check your configuration: ``` hostname1 (config) # show policymgr interfaces ``` ``` Policy enabled: yes ``` ``` Interface A  Active   : yes  op mode  : block (blocking)  fail-safe: open  policy   : mixed  tolerance: 1  Ports    : pether3  pether4 ``` To configure NX Appliance2 - NX Appliance *n* to connect to one or more proxy servers: 1. Enable the CLI configuration mode: `hostname > enable` `hostname # configure terminal` 2. Configure pair A (interfaces A1 and A2) in inline block mode on each NX Appliance2–NX Appliance*n*: `hostname (config) # policymgr interface A op-mode block fail-safe open policy-type mixed` `hostname (config) # policymgr interface A re-configure` 3. Save your changes: `hostname (config) # write memory` 4. Configure interface A2 to allow incoming traffic from the proxy server to pass through unblocked on each appliance connected to a proxy server: `hostname (config) # policymgr network host <Proxy_IP_address> interface A2 allow` where `Proxy_IP_address` is the IP address of the server. 5. Save your changes: `hostname (config) # write memory` 6. Check your configuration: `hostname (config) # show policymgr interfaces` ``` Policy enabled: yes ``` ``` Interface A  Active   : yes  op mode  : block (blocking)  fail-safe: open  policy   : mixed  tolerance: 1  Ports    : pether3  pether4 ```