--- title: "Configuring NTP authentication using the CLI" slug: "configuring-ntp-authentication-using-the-cli-2" updated: 2026-08-25T21:17:48Z published: 2026-08-25T21:17:48Z canonical: "docs.trellix.com/configuring-ntp-authentication-using-the-cli-2" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring NTP authentication using the CLI This topic describes how to configure NTP authentication using the CLI. ### Enabling NTP authentication and configuring keys Perform the tasks in this section in the order shown to configure NTP authentication. Obtain the authentication keys from the NTP server: 1. On the NTP server, map a key ID from 1–16 to an MD5 or SHA1 hash value. 2. Repeat the previous step for additional key ID/value pairs. 3. Copy and paste the key ID/value pairs so they can be configured on the appliance later in this procedure. Enable NTP and NTP authentication: 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. View the current status. ``` hostname (config) # show ntp configured ``` 3. If` NTP enabled: no `appears in the command output, enable NTP. ``` hostname (config) # ntp enable ``` 4. If` NTP Authentication enabled: no `appears is the command output, enable NTP authentication. ``` hostname (config) # ntp authentication enable ``` Define the authentication keys: 1. Use the following command to configure the key ID and hash value you obtained from the NTP server: ``` hostname (config) # ntp authentication key hash ``` where: - `<number> `is an integer from **1**–**16** - `<type> `is **md5** or **sha1** - `<value> `is the hash value 2. Repeat the previous step for each key you want to define. 3. View the configured keys. ``` hostname (config) # show ntp authentication configured ``` 4. Save your changes. ``` hostname (config) # write memory ``` Assign the keys to the NTP servers: 1. To assign a key to an NTP server, use the `ntp server <server> authentication key <number>` command, where` <server> `is the IP address or hostname of the NTP server, and` <number> `is the integer that you assigned to the key in the previous task The following example assigns hash key 1 to the NTP server 0.acme.pool.ntp.org: ``` hostname (config) # ntp server 0.acme.pool.ntp.org authentication key 1 ``` 2. Repeat the previous step for each key you want to define. 3. View the assigned keys: ``` hostname (config) # show ntp configured ``` 4. Verify that the keys are valid: ``` hostname (config) # show ntp authentication ``` 5. Save your changes: ``` hostname (config) # write memory ``` ### Disabling NTP authentication and removing keys You cannot delete an authentication key from the system if it is mapped to an NTP server. If a key is mapped to an NTP server, you must disable NTP authentication on that server before you delete the key. To disable NTP authentication on the system: 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. Disable NTP authentication: ``` hostname (config) # no ntp authentication ``` 3. Save your changes: ``` hostname (config) # write memory ``` To disable NTP authentication on a specific server: 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. To disable NTP authentication with a specified NTP server, use the` no ntp server <server> authentication `command, where` <server> `is the hostname or IP address of the NTP server. The following example disables NTP authentication with the NTP server with hostname 1.acme.pool.ntp.org: ``` hostname (config) # no ntp server 1.acme.pool.ntp.org authentication ``` 3. Save your changes: ``` hostname (config) # write memory ``` To delete an NTP authentication key: 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. To delete a key, use the` no ntp authentication key <number> `command, where` <number> `is the key ID. ``` hostname (config) # no ntp authentication key 1 ``` 3. Save your changes: ``` hostname (config) # write memory ``` ### Examples The following example shows the current configuration. ``` hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` The following example defines two authentication keys and assigns each one to an NTP server. ``` hostname (config) # ntp authentication key 1 hash md5 153ffa51cc765fb257e384e8e6aec8fe ``` ``` hostname (config) # ntp server 0.acme.pool.ntp.org key 1 ``` ``` hostname (config) # ntp authentication key 2 hash sha1 27a048b642be47d50a9c38427495945429597d91 ``` ``` hostname (config) # ntp server 1.acme.pool.ntp.org key 2 hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: 1 NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: 2 NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` ``` hostname (config) # show ntp authentication configured NTP enabled: yes NTP Authentication enabled: yes NTP Key Number 1  Type: md5  Key: 153ffa51cc765fb257e384e8e6aec8fe NTP Key Number 2  Type: sha1  Key: 27a048b642be47d50a9c38427495945429597d91 hostname (config) # show ntp authentication NTP is administratively enabled. NTP authentication is administratively enabled. Active servers and peers: Address           auth      keyid ===================================== 172.16.2.3        ok         1 10.30.4.3         ok         2 192.168.10.12     none       none ``` The following example disables NTP authentication on the 1.acme.pool.ntp.org server and then deletes the key it was using from the system. ``` hostname (config) # no ntp server 1.acme.pool.ntp.org authentication hostname (config) # no ntp authentication key 2 ``` :