--- title: "Configuring NTP servers using the CLI" slug: "configuring-ntp-servers-using-the-cli-4" tags: ["Product Usage", "CMS 11.x", "EX 11.x", "FX 11.x", "AX 11.x", "NX 11.x", "IVX 11.x", "Network Security"] updated: 2026-08-24T20:40:08Z published: 2026-08-24T20:40:08Z canonical: "docs.trellix.com/configuring-ntp-servers-using-the-cli-4" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring NTP servers using the CLI Use the commands in this topic to configure NTP servers. > [!NOTE] > Note > > See [Configuring NTP authentication using the CLI](/network-and-platform/docs/configuring-ntp-authentication-using-the-cli) for information about ensuring that the system clocks are only updated if the time is obtained from a trusted source. **To enable and configure NTP servers:** 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. Enable NTP synchronization: ``` hostname (config) # ntp enable ``` 3. Specify the primary NTP server: ``` hostname (config) # ntp server ``` where `<server>` is the IPv4 or IPv6 address, or hostname of the NTP server. 4. Repeat the previous step for the secondary NTP server and any additional NTP servers. **To change the NTP version:** 1. Specify the version: ``` hostname (config) # ntp ``` 2. To change the version on an NTP server: ``` hostname (config) ntp server version ``` where `<server>` is the IPv4 or IPv6 address, or hostname of the NTP server, and `<version>` is either **3** or **4** 3. To change the version on an NTP peer: ``` hostname (config) ntp peer version ``` where `<peer>` is the IPv4 or IPv6 address, or hostname of the NTP peer, and `<version>` is either **3** or **4**. 4. Save your changes: ``` hostname (config) # write memory ``` **To disable NTP:** 1. Disable NTP synchronization: ``` hostname (config) # ntp disable ``` *or* ``` hostname (config) # no ntp enable ``` 2. Save your changes: ``` hostname (config) # write memory ``` **To synchronize the system time with a specific NTP server one time:** 1. Synchronize the system time: ``` hostname (config) # ntpdate ``` where `<server>` is the IPv4 or IPv6 address, or hostname of the NTP server to synchronize with. 2. Save your changes: ``` hostname (config) # write memory ``` **To view the current NTP runtime state and configuration:** 1. Go to CLI standard mode. 2. View the information: ``` hostname > show ntp ``` **To view the configured NTP servers and their settings:** 1. Go to CLI standard mode. 2. View the information: ``` hostname > show ntp configured ``` ### Examples The following example configures two NTP servers and an NTP peer. ``` hostname (config) # ntp server 0.acme.pool.ntp.org hostname (config) # ntp server 1.acme.pool.ntp.org hostname (config) # ntp peer 5.acme.pool.ntp.org hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes NTP peer 5.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` The following example disables NTP synchronization on the system. ``` hostname (config) # no ntp enable hostname (config) # show ntp configured NTP enabled: no NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  ... hostname (config) # show ntp NTP is administratively disabled. NTP Authentication is administratively enabled. Clock is unsynchronized. No NTP associations present. ``` The following example temporarily disables NTP on the "3.acme.pool.ntp.org" server. ``` hostname (config) # ntp server 3.acme.pool.ntp.org disable hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  ... NTP server 3.acme.pool.ntp.org  Enabled: no  ... ``` The following example removes the "2.acme.pool.ntp.org" NTP server. ``` hostname (config) # no ntp server 2.acme.pool.ntp.org ``` The following example synchronizes the system clock with the NTP server. ``` hostname (config) # ntpdate 0.acme.pool.ntp.org adjust time server 192.168.120.23 offset -0.023716 sec ``` The following example changes the NTP version on the "3.acme.pool.ntp.org" server to version 3. ``` hostname (config) # ntp server 3.acme.pool.ntp.org version 3 hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. ... NTP server 3.acme.pool.ntp.org  Enabled: yes  NTP version: 3  Key: none ``` The following example shows the current NTP runtime state and configuration. ``` hostname > show ntp NTP is administratively enabled. NTP Authentication is administratively enabled. Clock is synchronized. Reference: 10.255.34.6  Offset: 1.713 ms. Active servers and peers:                                                           Poll    Last             Conf                     Offset   Ref         Interv  Resp Address      Type  Status     Stratum (msec)   Clock       (sec)   (sec) =========================================================================== 192.168.1.1  n/a   candidat (+)   2   -0.233   10.2.3.4      64     60 10.2.3.4     n/a   outlyer  (-)   2   12.069   192.168.2.2   64     50 172.16.4.5   n/a   candidat (+)   2   -0.958   10.5.6.7      64     50 10.255.34.6  n/a   sys.peer (*)   2   1.713    172.16.3.4    64     45 ``` The following example shows the configured NTP servers and their settings: ``` hostname > show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 3.acme.pool.ntp.org  Enabled: yes  NTP version: 4 ```