--- title: "Configuring NTP servers using the CLI" slug: "configuring-ntp-servers-using-the-cli" updated: 2026-09-30T17:04:33Z published: 2026-09-30T17:04:33Z canonical: "docs.trellix.com/configuring-ntp-servers-using-the-cli" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring NTP servers using the CLI Use the commands in this topic to configure NTP servers. ### Note See [Configuring NTP authentication using the CLI](/network-and-platform/docs/configuring-ntp-authentication-using-the-cli) for information about ensuring that the system clocks are only updated if the time is obtained from a trusted source. To enable and configure NTP servers: 1. Go to CLI configuration mode: ```plaintext hostname > enable hostname # configure terminal ``` 2. Enable NTP synchronization: ```plaintext hostname (config) # ntp enable ``` 3. Specify the primary NTP server: ```plaintext hostname (config) # ntp server ``` where` <server> `is the IPv4 or IPv6 address, or hostname of the NTP server. 4. Repeat the previous step for the secondary NTP server and any additional NTP servers. To change the NTP version: 1. Specify the version: ```plaintext hostname (config) # ntp ``` 2. To change the version on an NTP server: ```plaintext hostname (config) ntp server version ``` where` <server> `is the IPv4 or IPv6 address, or hostname of the NTP server, and` <version> `is either **3** or **4** 3. To change the version on an NTP peer: ```plaintext hostname (config) ntp peer version ``` where` <peer> `is the IPv4 or IPv6 address, or hostname of the NTP peer, and` <version> `is either **3** or **4**. 4. Save your changes: ```plaintext hostname (config) # write memory ``` To disable NTP: 1. Disable NTP synchronization: ```plaintext hostname (config) # ntp disable ``` *or* ```plaintext hostname (config) # no ntp enable ``` 2. Save your changes: ```plaintext hostname (config) # write memory ``` To synchronize the system time with a specific NTP server one time: 1. Synchronize the system time: ```plaintext hostname (config) # ntpdate ``` where` <server> `is the IPv4 or IPv6 address, or hostname of the NTP server to synchronize with. 2. Save your changes: ```plaintext hostname (config) # write memory ``` To view the current NTP runtime state and configuration: 1. Go to CLI standard mode. 2. View the information: ```plaintext hostname > show ntp ``` To view the configured NTP servers and their settings: 1. Go to CLI standard mode. 2. View the information: ```plaintext hostname > show ntp configured ``` ### Examples The following example configures two NTP servers and an NTP peer. ```plaintext hostname (config) # ntp server 0.acme.pool.ntp.org hostname (config) # ntp server 1.acme.pool.ntp.org hostname (config) # ntp peer 5.acme.pool.ntp.org hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes NTP peer 5.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` The following example disables NTP synchronization on the system. ```plaintext hostname (config) # no ntp enable hostname (config) # show ntp configured NTP enabled: no NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  ... hostname (config) # show ntp NTP is administratively disabled. NTP Authentication is administratively enabled. Clock is unsynchronized. No NTP associations present. ``` The following example temporarily disables NTP on the "3.acme.pool.ntp.org" server. ```plaintext hostname (config) # ntp server 3.acme.pool.ntp.org disable hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  ... NTP server 3.acme.pool.ntp.org  Enabled: no  ... ``` The following example removes the "2.acme.pool.ntp.org" NTP server. ```plaintext hostname (config) # no ntp server 2.acme.pool.ntp.org ``` The following example synchronizes the system clock with the NTP server. ```plaintext hostname (config) # ntpdate 0.acme.pool.ntp.org adjust time server 192.168.120.23 offset -0.023716 sec ``` The following example changes the NTP version on the "3.acme.pool.ntp.org" server to version 3. ```plaintext hostname (config) # ntp server 3.acme.pool.ntp.org version 3 hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. ... NTP server 3.acme.pool.ntp.org  Enabled: yes  NTP version: 3  Key: none ``` The following example shows the current NTP runtime state and configuration. ```plaintext hostname > show ntp NTP is administratively enabled. NTP Authentication is administratively enabled. Clock is synchronized. Reference: 10.255.34.6  Offset: 1.713 ms. Active servers and peers:                                                           Poll    Last             Conf                     Offset   Ref         Interv  Resp Address      Type  Status     Stratum (msec)   Clock       (sec)   (sec) =========================================================================== 192.168.1.1  n/a   candidat (+)   2   -0.233   10.2.3.4      64     60 10.2.3.4     n/a   outlyer  (-)   2   12.069   192.168.2.2   64     50 172.16.4.5   n/a   candidat (+)   2   -0.958   10.5.6.7      64     50 10.255.34.6  n/a   sys.peer (*)   2   1.713    172.16.3.4    64     45 ``` The following example shows the configured NTP servers and their settings: ```plaintext hostname > show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 3.acme.pool.ntp.org  Enabled: yes  NTP version: 4 ``` :