--- title: "Configuring the dual-interface LAN option using the CLI" slug: "configuring-the-dual-interface-lan-option-using-the-cli-1" tags: ["Central Management System", "Install and Get Started"] updated: 2026-10-01T15:10:58Z published: 2026-10-01T15:10:58Z canonical: "docs.trellix.com/configuring-the-dual-interface-lan-option-using-the-cli-1" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring the dual-interface LAN option using the CLI Use the commands in this section to configure the basic settings for a dual-interface Central Management System cluster in a LAN deployment that uses non-default interfaces. ### Configuring the primary node Perform the procedures in this section in order to configure the primary node. **Configure the default HA interface:** 1. Configure the default HA interface address: ```plaintext node1-hostname (config) # interface ip address / ``` where `<ip address>` is the IPv4 address of the default HA interface and `<mask>` is the mask length prefixed by a slash (for example,` /24`) or a netmask (for example,` 255.255.255.0`). 2. Prevent the default HA interface from becoming disabled: ```plaintext node1-hostname (config) # no interface shutdown ``` - Enable the interface as the default HA interface: ```plaintext node1-hostname (config) # ha interface default ``` **Configure the backup HA interface:** 1. Configure the backup HA interface address: ```plaintext node1-hostname (config) # interface ip address / ``` where `<ip address>` is the IPv4 address of the backup HA interface and `<mask>` is the mask length prefixed by a slash (for example,` /24`) or a netmask (for example`, 255.255.255.0`). 2. Prevent the backup HA interface from becoming disabled: ```plaintext node1-hostname (config) # no interface shutdown ``` 3. Enable the interface as the backup HA interface: ```plaintext node1-hostname (config) # ha interface backup ``` **Verify and save your changes:** 1. Verify your changes: ```plaintext node1-hostname (config) # show ha configuration ``` 2. Save your changes: ```plaintext node1-hostname (config) # write memory ``` **Start the cluster engine:** 1. Start the cluster engine: ```plaintext node1-hostname (config) # ha engine restart ``` 2. Wait for all services to be in the "running" state: ```plaintext node1-hostname (config) # show ha status ``` ### Configuring the secondary node Perform the procedures in this section in order to configure the secondary node. **Configure the default HA interface:** 1. Configure the default HA interface address: ```plaintext node2-hostname (config) # interface ip address / ``` where `<ip address>` is the IPv4 address of the default HA interface and `<mask>` is the mask length prefixed by a slash (for example,` /24`) or a netmask (for example,` 255.255.255.0`). 2. Prevent the default HA interface from becoming disabled: ```plaintext node2-hostname (config) # no interface shutdown ``` 3. Enable the interface as the default HA interface: ```plaintext node2-hostname (config) # ha interface default ``` **Configure the backup HA interface:** 1. Configure the backup HA interface address: ```plaintext node2-hostname (config) # interface ip address / ``` where `<ip address>` is the IPv4 address of the backup HA interface and `<mask>` is the mask length prefixed by a slash (for example,` /24`) or a netmask (for example`, 255.255.255.0`). 2. Prevent the backup HA interface from becoming disabled: ```plaintext node2-hostname (config) # no interface shutdown ``` 3. Enable the interface as the backup HA interface: ```plaintext node2-hostname (config) # ha interface backup ``` **Add the node to the cluster:** 1. Add the node to the cluster: ```plaintext node2-hostname (config) # ha node join ``` 2. When prompted, enter the password for the primary node's remote admin user: ```plaintext Enter password for admin account on primary node: ******** ``` **Verify and save your changes:** 1. Verify your changes: ```plaintext node2-hostname (config) # show ha configuration ``` 2. Save your changes: ```plaintext node2-hostname (config) # write memory ``` **Start the cluster engine:** 1. Start the cluster engine: ```plaintext node2-hostname (config) # ha engine restart ``` 2. Wait for all services to be in the "running" state: ```plaintext node2-hostname (config) # show ha status ``` ### Note You can perform a manual failover to test the cluster.Failing over manually using the CLI ### Examples The following example configures the primary node in the dual-interface LAN deployment using non-default interfaces. ```plaintext node1 (config) # interface ether3 ip address 10.0.0.1 /30 node1 (config) # no interface ether3 shutdown node1 (config) # ha interface default ether3 node1 (config) # interface ether2 ip address 10.1.1.1 /30 node1 (config) # no interface ether2 shutdown node1 (config) # ha interface backup ether2 node1 (config) # show ha configuration ... node1 (config) # write memory node1 (config) # ha engine restart ... node1 (config) # show ha status ... ``` The following example configures the secondary node in the dual-interface LAN deployment using non-default interfaces. ```plaintext node2 (config) # interface ether3 ip address 10.0.0.2 /30 node2 (config) # no interface ether3 shutdown node2 (config) # ha interface default ether3 node2 (config) # interface ether2 ip address 10.0.1.2 /30 node2 (config) # no interface ether2 shutdown node2 (config) # ha interface backup ether2 node2 (config) # ha node join 172.16.127.144 Enter password for admin account on primary node: ******** Node joining has started Please check the status with CLI 'show ha configuration'. node2 (config) # show ha configuration ... node2 (config) # write memory node2 (config) # ha engine restart ... node2 (config) # show ha status ... ```