--- title: "Configuring the NX to forward traffic from a mirror port using the CLI" slug: "configuring-the-nx-to-forward-traffic-from-a-mirror-port-using-the-cli" tags: ["Network Security (NX)"] updated: 2026-08-24T22:01:11Z published: 2026-08-24T22:01:11Z canonical: "docs.trellix.com/configuring-the-nx-to-forward-traffic-from-a-mirror-port-using-the-cli" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring the NX to forward traffic from a mirror port using the CLI Use the commands in this section to configure port mirroring. To configure a mirror port on an interface: 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. View the interface configuration: ``` hostname (config) # show policymgr interfaces ``` 3. If the interface pair with the mirror port is not already in tap mode, change it: ``` hostname (config) # policymgr interface op-mode tap hostname (config) # policymgr interface re-configure ``` where `<interfacePair>` is the interface pair designation. 4. Configure the mirror port: ``` hostname (config) # policymgr interface mirror port ``` where `<interfacePair>` is the interface pair from which traffic will be forwarded, and `<portName>` is the port that will receive the mirrored traffic. 5. Verify your change: ``` hostname (config) # show policymgr interfaces ``` 6. Save your change: ``` hostname (config) # write memory ``` > [!NOTE] > Note > > If you configure multiple mirror ports for the same interface pair in the same session, the last port you configure takes effect. In the following example, pether6 is overwritten by pether9. > > ``` > hostname (config) # policymgr interface A mirror port pether6 > hostname (config) # policymgr interface A mirror port pether9 > ``` To clear a mirror port from an interface: 1. Go to CLI configuration mode: ``` hostname > enable hostname # configure terminal ``` 2. Clear the mirror port: ``` hostname (config) # policymgr interface mirror clear ``` 3. Verify your change: ``` hostname (config) # show policymgr interfaces ``` 4. Save your change: ``` hostname (config) # write memory ``` ##### Examples The following example displays the current interface pairs and their status, and then configures pether6 on Interface B as the mirror port for the monitoring traffic on Interface A. ``` hostname (config) # show policymgr interfaces Policy enabled : yes Interface A  Active       : yes  op mode      : monitor (permissive)  fail-safe    : close  policy       : mixed  tolerance    : 1  mirror-port  :  Ports        : pether3 pether4  QinQ         : no  QinQ-evet    : 0x88a8 Interface B  Active       : yes  op-mode      : tap (tapping)  fail-safe    : close  policy       : mixed  tolerance    : 1  mirror-port  :  Ports        : pether5 pether6  QinQ         : no  QinQ-evet    : 0x88a8 Interface C  Active       : yes  op mode      : tap (tapping)  fail-safe    : close  policy       : mixed  tolerance    : 1  mirror-port  :  Ports        : pether7 pether8  QinQ         : no  QinQ-evet    : 0x88a8 Interface D  Active       : yes  op mode      : tap (tapping)  fail-safe    : close  policy       : mixed  tolerance    : 1  mirror-port  :  Ports        : pether9 pether10  QinQ         : no  QinQ-evet    : 0x88a8 hostname (config) # policymgr interface A mirror port pether6 hostname (config) # show policymgr interfaces Policy enabled : yes Interface A  Active       : yes  op mode      : monitor (permissive)  fail-safe    : close  policy       : mixed  tolerance    : 1  mirror-port  : pether6  Ports        : pether3 pether4  QinQ         : no  QinQ-evt     : 0x88a8 ... ``` The following example clears port mirroring on Interface A. ``` hostname (config) # policymgr interface A mirror clear ``` The following example configures pether6 as the mirror port for both Interface A and Interface D. ``` hostname (config) # policymgr interface A mirror port pether6 hostname (config) # policymgr interface D mirror port pether6 ``` The following example configures pether6 as the mirror port for Interface A and pether9 as the mirror port for Interface C. ``` hostname (config) # policymgr interface A mirror port pether6 hostname (config) # policymgr interface C mirror port pether9 ``` ##### Configuring NX to handle QinQ traffic When the NX appliance is receiving only QinQ traffic on a port pair, enabling QinQ mode on those ports is essential for proper handling of packets/traffic. In this case, it is essential to enable QinQ mode on the specified port pair to avoid latency or datapath related issues. When the NX appliance is receiving mixed traffic (no vLAN tag, single vLAN tag, and double vLAN tag QinQ traffic) on a port pair, it is important to separate the QinQ (doble vLAN) traffic to different port pair and enable QinQ mode on that respective port pair for optimal performance and proper handling. The following example displays commands to enable QinQ mode: ``` NX-2500-254 (config) # policymgr interface A qinq ? evet                 Configure interface QinQ external vlan ether type evlan                Configure interface QinQ flag hostname (config) # policymgr interface A qinq evlan enable hostname (config) # policymgr interface A qinq evet 0x? 0x88a8 802.1ad ether type 0x9100 802.1QinQ ether type 0x8100 802.1Q ether type hostname (config) # policymgr interface A qinq evet 0x8100 hostname (config) # policymgr interface A re-configure ```