--- title: "Configuring the Single-Interface LAN Option Using the Wizard" slug: "configuring-the-single-interface-lan-option-using-the-wizard" tags: ["Central Management System", "Install and Get Started"] updated: 2026-08-21T19:17:36Z published: 2026-08-21T19:17:36Z canonical: "docs.trellix.com/configuring-the-single-interface-lan-option-using-the-wizard" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Configuring the Single-Interface LAN Option Using the Wizard Use the commands and configuration wizard instructions in this section to configure the basic settings for a single-interface Central Management System cluster in a LAN deployment that uses a non-default interface. Configure the primary node: 1. Enable the CLI configuration mode: ```plaintext node1-hostname > enable node1-hostname # configure terminal ``` 2. Start the configuration wizard: ```plaintext node1-hostname (config) # configuration jump-start ``` 3. Respond to the basic Central Management System configuration questions the wizard asks, as described in the *Central Management System Administration Guide*. 4. Respond to the cluster configuration questions the wizard asks, as described below. Configure CM HA? Enter **yes**. CM HA uses ether1 as CM HA default interface. Do you want to change CM HA interfaces? Enter **yes**. CM HA default interface name? Enter the name of the default HA interface. CM HA default interface IPv4 address and masklen? Enter the default HA interface IPv4 address and mask length. Configure CM HA default interface gateway? Enter **no**. Neighbor node CM HA default interface IPv4 address and masklen? Enter the other node's default HA interface IPv4 address and mask length. Do you want to configure CM HA backup interface? Enter **no**. Configure this node as primary CM HA node? Enter **yes**. 5. Wait for all services to be in the "running" state: ```plaintext node1-hostname (config) # show ha status ``` Configure the secondary node: 1. Enable the CLI configuration mode: ```plaintext node2-hostname > enable node2-hostname # configure terminal ``` 2. Start the configuration wizard: ```plaintext node2-hostname (config) # configuration jump-start ``` 3. Respond to the basic Central Management System configuration questions the wizard asks, as described in the *Central Management System Administration Guide*. 4. Respond to the cluster configuration questions the wizard asks, as described below. Configure CM HA? Enter **yes**. CM HA uses ether1 as CM HA default interface. Do you want to change CM HA interfaces? Enter **yes**. CM HA default interface name? Enter the name of the default HA interface. CM HA default interface IPv4 address and masklen? Enter the default HA interface IPv4 address and mask length. Configure CM HA default interface gateway? Enter **no**. Neighbor node CM HA default interface IPv4 address and masklen? Enter the other node's default HA interface IPv4 address and mask length. Do you want to configure CM HA backup interface? Enter **no**. Configure this node as primary CM HA node? Enter **no**. CM HA primary node IP address? Enter the IPv4 address of the primary node. CM HA primary node admin account password? Enter the password for the primary node's remote admin user. Confirm CM HA primary node admin account password? Re-enter the password for the primary node's remote admin user. ### Note You can perform a manual failover to test the cluster.Failing over manually using the CLI ### Examples The following example shows the wizard steps used to configure the primary node using the single-interface LAN option. ```plaintext ... Step 14: CM HA uses ether1 as CM HA default interface. Do you want to change CM HA interfaces? [yes] yes Step 15: CM HA default interface name? [ether1] ether3 Step 16: CM HA default interface IPv4 address and masklen? [0.0.0.0/0] 10.0.0.1/30 Step 17: Configure CM HA default interface gateway? [no] no Step 18: Neighbor node CM HA default interface IPv4 address and masklen? 10.0.0.2/30 Step 19: Do you want to configure CM HA backup interface? [yes] no Step 20: Configure this node as primary CM HA node? [no] yes ... Starting CM HA engine Configuration changes saved. ... ``` The following example shows the wizard steps used to configure the secondary node using the single-interface LAN option. ```plaintext ... Step 14: CM HA uses ether1 as CM HA default interface. Do you want to change CM HA interfaces? [yes] yes Step 15: CM HA default interface name? [ether1] ether3 Step 16: CM HA default interface IPv4 address and masklen? [0.0.0.0/0] 10.0.0.2/30 Step 17: Configure CM HA default interface gateway? [no] no Step 18: Neighbor node CM HA default interface IPv4 address and masklen? 10.0.0.1/30 Step 19: Do you want to configure CM HA backup interface? [yes] no Step 20: Configure this node as primary CM HA node? [no] no Step 21: CM HA primary node IP address? 172.16.127.144 Step 22: CM HA primary node admin account password? ******** Step 23: Confirm CM HA primary node admin account password? ******** ... Initiated CM HA node joining Node joining has started Please check the status with CLI 'show ha configuration'. ... Starting CM HA engine Configuration changes saved. ... ``` :