--- title: "Enable tap mode for the Active Fail-Open module" slug: "enable-tap-mode-for-the-active-fail-open-module" tags: ["Hardware", "IPS 11.1.x"] updated: 2026-08-19T18:44:11Z published: 2026-09-17T07:33:47Z canonical: "docs.trellix.com/enable-tap-mode-for-the-active-fail-open-module" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Enable tap mode for the Active Fail-Open module **Prerequisites:** - Configure an IPv4 address for your 100G Active Fail-Open chassis. - Make sure you can access the 100G Active Fail-Open chassis web interface using a web browser. You can enable tap mode for your 100G Active Fail-Open chassis if you use a tap to route network traffic to the Sensor monitoring ports. **Steps:** 1. Login to the web interface of the 100G Active Fail-Open chassis. Use default credentials to access the web interface. 2. To manage bypass/tap mode manually, go to **AFO Configuration** → **Module ** → **Heartbeat Setting**. ![GUID-7EC40BE7-341B-45FF-9727-07E825AD1147-low.jpg](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-2e4754b1-b3b9-df83-8505-b8574ab30b96.jpg?sv=2026-02-06&spr=https&st=2026-11-20T20%3A19%3A42Z&se=2026-11-20T21%3A19%3A42Z&sr=c&sp=r&sig=34De75YIpuwnaiJfIbc8EXUI4ZCM7agj%2F4yfP1VacvQ%3D) 3. To enter bypass/tap mode manually, de-select **Heartbeat Active Mode**. > [!NOTE] > Note > > - By deselecting this option, no heartbeat packets will be sent from the Active Fail-Open module to the Sensor monitoring ports. > - To restore the normal Active Fail-Open kit function, select this option. 4. In **Active OP Mode**, select **TAP** mode from the drop-down. > [!NOTE] > Note > > By default, **Inline** mode is selected. ![GUID-35EFDC6D-28B2-4497-AC40-E301AA31B388-low.jpg](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-248085fb-73d4-16fa-b16a-dd3edd1dcbac.jpg?sv=2026-02-06&spr=https&st=2026-11-20T20%3A19%3A42Z&se=2026-11-20T21%3A19%3A42Z&sr=c&sp=r&sig=34De75YIpuwnaiJfIbc8EXUI4ZCM7agj%2F4yfP1VacvQ%3D) 5. Click **Commit**. 6. To save your configuration, select the **Save** tab. Click **Save**. ![GUID-96F4E74A-5212-4AD5-A77D-CFC5CCB07B45-low.jpg](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-b2db946f-d01c-3377-302e-4be95c6dae3f.jpg?sv=2026-02-06&spr=https&st=2026-11-20T20%3A19%3A42Z&se=2026-11-20T21%3A19%3A42Z&sr=c&sp=r&sig=34De75YIpuwnaiJfIbc8EXUI4ZCM7agj%2F4yfP1VacvQ%3D) **Result:** You have set your Active Fail-Open module to operate in tap mode.