--- title: "Enabling or disabling all the features of the Central Management System Peer Service on the peers using the CLI" slug: "enabling-disabling-features-central-management-system-peer-service-cli" updated: 2026-08-25T21:18:10Z published: 2026-08-25T21:18:10Z canonical: "docs.trellix.com/enabling-disabling-features-central-management-system-peer-service-cli" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Enabling or disabling all the features of the Central Management System Peer Service on the peers using the CLI Follow these steps to enable or disable all the features of the Central Management System Peer Service on each Central Management System peer using the CLI. To enable all the features of the Central Management System Peer Service: 1. Go to CLI configuration mode. ``` CMS1 > enable ``` ``` CMS1 # configure terminal ``` 2. Enable all the CM Peer Service features on a CM peer. ``` CMS1 (config) # cms peer enable ``` 3. Save your changes. ``` CMS1 (config) # write memory ``` 4. Repeat this procedure for each Central Management System peer. 5. Verify the status for all the connected Central Management System peers. The following example verifies that CMS1 is connected to CMS2. ``` CMS1 (config) # show cms peer-service ``` ``` CMS peer-service enabled:          yes ``` ``` ----------------------------------------------------------------------- ``` ``` CMS peer CMS2: ``` ```   Enabled:                     yes ``` ```   Hostname:                    CMS2 ``` ```   Address:                     172.16.216.51 ``` ```   Auth-token checksum:         360a37cc532b9e2e75b674eb3b5fe2e0 ``` ```   Interactions with peer: ``` ```      Distributed CMS Correlation: ``` ```         Enabled:                        yes ``` ```         Status:                         OK          @ 2016/01/27 18:58:51 ``` ```      Dynamic Threat Intelligence (DTI): ``` ```         Enabled:                        no ``` ```         Proxy mode:                     No proxy ``` ```         Status:                         UNKNOWN     @ N/A ``` ```      Update Peer: ``` ```         Enabled:                        yes ``` ```         Status:                         OK          @ 2016/01/27 18:56:30 ``` ``` -----------------------------------------------------------------------         ``` To disable all the features of the Central Management System Peer Service: 1. Go to CLI configuration mode. ``` CMS1 > enable CMS1 # configure terminal ``` 2. Disable all the Central Management System Peer Service features on a Central Management System peer. ``` CMS1 (config) # no cms peer enable ``` 3. Save your changes. ``` CMS1 (config) # write memory ``` 4. Repeat this procedure for each Central Management System peer. 5. Verify the status for all the Central Management System peers. The following example verifies that CMS1 is not connected to CMS2. ``` CMS1 (config) # show cms peer-service ``` ``` CMS peer-service enabled:          yes ``` ``` ----------------------------------------------------------------------- ``` ``` CMS peer CMS2: ``` ```   Enabled:                     no ``` ```   Hostname:                    CMS2 ``` ```   Address:                     172.16.216.51 ``` ```   Auth-token checksum:         360a37cc532b9e2e75b674eb3b5fe2e0 ``` ```   Interactions with peer: ``` ```      Distributed CMS Correlation: ``` ```         Enabled:                        yes ``` ```         Status:                         OK          @ 2016/01/27 18:58:51 ``` ```       Dynamic Threat Intelligence (DTI): ``` ```          Enabled:                        no ``` ```          Proxy mode:                     No proxy ``` ```          Status:                         UNKNOWN     @ N/A ``` ```       Update Peer: ``` ```          Enabled:                        yes ``` ```          Status:                         OK          @ 2016/01/27 18:58:51 ``` ``` ----------------------------------------------------------------------- ``` :