--- title: "Initial configuration" slug: "initial-configuration-10" tags: ["Install and Get Started", "NDR 4.x", "Customer", "Network Security"] updated: 2026-11-17T09:23:23Z published: 2026-11-17T09:23:23Z canonical: "docs.trellix.com/initial-configuration-10" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Initial configuration This chapter contains information and instructions for configuring basic network settings for yourNDR appliance using the CLI. > [!WARNING] > Important > > Trellix highly recommends using the CLI to modify your NDR appliance configuration settings. Trellix does not provide technical support for configuration changes made using the shell. (DOC-958) ### Network information requirements The table below provides the network information requirements. | Network Item | Information Needed | | --- | --- | | NDR Appliance | - Cluster name - name for all of the appliances in the same location. - Hostname - unique name for each appliance. > [!WARNING] > Caution > > Elasticsearch does not allow index names with uppercase characters. Cluster names, which are used to create index names, and hostnames must be lowercase when entered in KLISH. - IP address - Subnet mask - Default gateway address | | Domain Name Service (DNS) | IP address of one or more DNS Servers | | Network Time Protocol (NTP) Service (Optional) | IP address of one or more NTP servers | | IPMI (Optional) | If you want to access the appliance remotely using the IPMI: - IPMI IP address - IPMI subnet mask - IPMI gateway address | ### Initial configuration procedure After your Network Detection and Response appliance has been physically added to your network, you must configure the appliance settings during the first boot. For initial configuration, you need a USB keyboard and a monitor with a VGA connection to the appliance. 1. Connect the USB keyboard and monitor to the appliance. 2. Power up the appliance. 3. Press **Enter** to review the EULA. 4. Review the EULA and type `q` when you are finished. Accept the EULA: ``` Do you accept the FireEye End USer License Agreement?: accept ``` 5. Press **Enter**. 6. Enter the hostname. The hostname must be different from the Cluster name, but will also be used as the Cluster node name. For example: `Hostname: cinnamon` > [!WARNING] > Important > > Elasticsearch does not allow index names with uppercase characters. Cluster names, which are used to create index names, and hostnames must be lowercase when entered in CLI. 7. If the NDR is a Data Node within a multi-box cluster: Enter ``` y ``` . If the NDR is a standalone appliance or a Master-Data Node within a multi-box cluster: Enter `n`. 8. Enter the Cluster name. This must be different from the hostname. For example: `Cluster name: cinnamon-cluster` 9. Press **Enter**. 10. You must change your npadmin, npscp, and IPMI passwords. > [!WARNING] > Important > > The password must meet the following criteria: > > - 8 characters minimum > - Contain at least 1 character from each of the following categories: > > - Uppercase alphabet (A-Z) > - Lowercase alphabet (a-z) > - Numbers (0-9) > - Symbols (!,?, @, etc.) 11. Press any key to continue after you update all three passwords. 12. To customize your system, enter `y`. Continue below with Configuring Network Settings. ### Configuring network settings Reference the steps below to complete the initial configuration. If you press enter without providing a new value in any of the following steps, a default value shown inside brackets is used. IP addressed provided must be in valid dotted quad notation. DNS and NTP server addresses must be separated with spaces. 1. Enter the IP address type. If the IP address is a static address, enter `S`. If the IP address is a DHCP address, enter `D`. Press **Enter**. 2. Enter the routable IP address for the appliance. Press **Enter**. 3. Enter the netmask address. Press **Enter**. 4. Press **Enter** when prompted `Routable IPv6 Address? [ ]:`. 5. Press **Enter** when prompted `Prefix Length? [ ]:`. 6. Enter the IPv4 address gateway. Press **Enter**. 7. Enter the DNS address. Press **Enter**. 8. Enter the search domain(s) if you will specify non-fully qualified NTP servers in the following step. If you will not provide an NTP server in the following step, press **Enter** when prompted `Search Domain(s) [ ]:`. 9. Enter a local NTP server, if available. Otherwise, press **Enter** to accept the default option. 10. Enter the IPMI IP address (Optional) or press **Enter** to accept the default option. 11. Enter the IPMI Netmask (Optional) or press **Enter** to accept the default option. 12. Enter the IPMI Gateway Address (Optional) or press **Enter** to accept the default option. 13. To enable the Ether 1 interface, enter `Y`. The Ether 1 interface is used for internal communication between multi-box NDR clusters and single-box clusters in multi-director configurations. 14. Your current settings are displayed. Enter `Y` to save your configuration. 15. You see the following prompt: `Do you want to rebuild storage? [y/n]:` It is not required to rebuild storage. Capture data on storage disk drives will be erased if you enter `y`. Enter `n`. Press **Enter**. The NDR restarts. ### Logging in 1. Log in with default admin username and the password you selected in the Initial Configuration Procedure. `hostname login: npadmin` `password: <password>` > [!NOTE] > Note > > Do not be alarmed if you see the following message after logging in to the NDR appliance: > > `SYSTEM CRITICAL - One or more processes (ia-eve-route acm caseengine flowsummaryservice scheduledsearchservice userprofileservice) not running` > > The services take some time to come up. Ia-eve-route will not come up until a metadata source is configured. To confirm that services are running, wait a few minutes and then use the `show status` command to show the same output. 2. Enter privileged mode: `npadmin@hostname> enable` 3. Enter the npadmin password. 4. Enter config mode: `configure system` You can now continue to set up the users, PX appliance communication, and other configuration settings for the NDR appliance.