--- title: "NTP server configuration" slug: "ntp-server-configuration-5" tags: ["Network Security (NX)"] updated: 2026-09-10T17:47:37Z published: 2026-09-10T17:47:37Z canonical: "docs.trellix.com/ntp-server-configuration-5" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # NTP server configuration Instead of manually setting the system date and time, you can specify one or more Network Time Protocol (NTP) servers and peers to synchronize the time automatically. By default, NTP version 4 is used, but you can specify version 3 instead. You can perform a one-time action that synchronizes the system clock with a specific NTP server. NTP is enabled by default. The appliance is pre-configured with four NTP servers your appliance can use if it can reach them. The appliance can authenticate that the time it obtains from an NTP server is from a known and trusted source. The system clock is updated only if a key ID in the incoming NTP packet matches a key ID configured on the appliance, and if that key ID is mapped to the same MD5 or SHA1 hash value stored on both the NTP server and the appliance. If the key ID/value pair on NTP server and appliance do not match, the clock is not updated. NTP authentication is enabled by default, but the NTP server must already have the key ID/value pair, and the same key ID/value pair must be configured on the appliance and then associated with the NTP server. A total of 16 keys can be configured on a single appliance. - [Configuring NTP servers using the Web UI](/network-and-platform/docs/ntp-server-configuration-5#configuring-ntp-servers-using-the-web-ui) - [Configuring NTP servers using the CLI](/network-and-platform/docs/ntp-server-configuration-5#configuring-ntp-servers-using-the-cli) - [Configuring NTP authentication using the CLI](/network-and-platform/docs/ntp-server-configuration-5#configuring-ntp-authentication-using-the-cli) Prerequisites - Admin access to configure NTP - Monitor, Operator, or Admin access to view NTP configuration and status information - Connectivity to at least one NTP server - *For NTP authentication*: Authentication key ID/value pairs on the NTP servers for which authentication will be configured ## Configuring NTP servers using the Web UI Use the **Enable NTP** section of the **Date and Time Settings** page to configure NTP servers. > [!NOTE] > Note > > The Intelligent Virtual Execution - Server appliance has a CLI and a Web UI. The recommended method for this configuration on a Intelligent Virtual Execution - Server appliance is through the Central Management System Web UI. ![All_Settings_DateNTP_scap.PNG](https://cdn.us.document360.io/0d453a50-e1da-4d4a-9409-fea7959614d8/Images/Documentation/uuid-7c3a854f-7bce-7056-39f9-51d743a8d1d7(4).png?sv=2026-02-06&spr=https&st=2026-11-20T07%3A13%3A45Z&se=2026-11-20T08%3A13%3A45Z&sr=c&sp=r&sig=SmVE%2FdA%2FXXIpAarnGvsM%2B7Afq0EnhmW0FepDhrOUrlQ%3D) To configure NTP servers: 1. Click the **Settings** tab. 2. Click **Date and Time** on the sidebar. 3. Click **Add NTP Server**. 4. Enter the IP address or hostname of the NTP server that you want to use in the **Add NTP Server** box. 5. Click **Add**. 6. Repeat the previous three steps to add additional servers. 7. To synchronize the system time once with a selected NTP server, click **Update** next to the server entry. The time is updated, and the needed adjustment is displayed in a message on the page. 8. To delete an NTP server, select the checkbox next to the server and then click **Remove NTP Server**. 9. Click **Yes** to confirm the action. ## Configuring NTP servers using the CLI Use the commands in this topic to configure NTP servers. > [!NOTE] > Note > > See [Configuring NTP authentication using the CLI](/network-and-platform/docs/ntp-server-configuration-5#configuring-ntp-authentication-using-the-cli) for information about ensuring that the system clocks are only updated if the time is obtained from a trusted source. To enable and configure NTP servers: 1. Go to CLI configuration mode: ```plaintext hostname > enable hostname # configure terminal ``` 2. Enable NTP synchronization: ```plaintext hostname (config) # ntp enable ``` 3. Specify the primary NTP server: ```plaintext hostname (config) # ntp server ``` where `<server>` is the IPv4 or IPv6 address, or hostname of the NTP server. 4. Repeat the previous step for the secondary NTP server and any additional NTP servers. To change the NTP version: 1. Specify the version: ```plaintext hostname (config) # ntp ``` 2. To change the version on an NTP server: ```plaintext hostname (config) ntp server version ``` where `<server>` is the IPv4 or IPv6 address, or hostname of the NTP server, and `<version>` is either **3** or **4** 3. To change the version on an NTP peer: ```plaintext hostname (config) ntp peer version ``` where `<peer>` is the IPv4 or IPv6 address, or hostname of the NTP peer, and `<version>` is either **3** or **4**. 4. Save your changes: ```plaintext hostname (config) # write memory ``` To disable NTP: 1. Disable NTP synchronization: ```plaintext hostname (config) # ntp disable ``` *or* ```plaintext hostname (config) # no ntp enable ``` 2. Save your changes: ```plaintext hostname (config) # write memory ``` To synchronize the system time with a specific NTP server one time: 1. Synchronize the system time: ```plaintext hostname (config) # ntpdate ``` where `<server>` is the IPv4 or IPv6 address, or hostname of the NTP server to synchronize with. 2. Save your changes: ```plaintext hostname (config) # write memory ``` To view the current NTP runtime state and configuration: 1. Go to CLI standard mode. 2. View the information: ```plaintext hostname > show ntp ``` To view the configured NTP servers and their settings: 1. Go to CLI standard mode. 2. View the information: ```plaintext hostname > show ntp configured ``` ### Examples The following example configures two NTP servers and an NTP peer. ```plaintext hostname (config) # ntp server 0.acme.pool.ntp.org hostname (config) # ntp server 1.acme.pool.ntp.org hostname (config) # ntp peer 5.acme.pool.ntp.org hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes NTP peer 5.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` The following example disables NTP synchronization on the system. ```plaintext hostname (config) # no ntp enable hostname (config) # show ntp configured NTP enabled: no NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  ... hostname (config) # show ntp NTP is administratively disabled. NTP Authentication is administratively enabled. Clock is unsynchronized. No NTP associations present. ``` The following example temporarily disables NTP on the "3.acme.pool.ntp.org" server. ```plaintext hostname (config) # ntp server 3.acme.pool.ntp.org disable hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  ... NTP server 3.acme.pool.ntp.org  Enabled: no  ... ``` The following example removes the "2.acme.pool.ntp.org" NTP server. ```plaintext hostname (config) # no ntp server 2.acme.pool.ntp.org ``` The following example synchronizes the system clock with the NTP server. ```plaintext hostname (config) # ntpdate 0.acme.pool.ntp.org adjust time server 192.168.120.23 offset -0.023716 sec ``` The following example changes the NTP version on the "3.acme.pool.ntp.org" server to version 3. ```plaintext hostname (config) # ntp server 3.acme.pool.ntp.org version 3 hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. ... NTP server 3.acme.pool.ntp.org  Enabled: yes  NTP version: 3  Key: none ``` The following example shows the current NTP runtime state and configuration. ```plaintext hostname > show ntp NTP is administratively enabled. NTP Authentication is administratively enabled. Clock is synchronized. Reference: 10.255.34.6  Offset: 1.713 ms. Active servers and peers:                                                           Poll    Last             Conf                     Offset   Ref         Interv  Resp Address      Type  Status     Stratum (msec)   Clock       (sec)   (sec) =========================================================================== 192.168.1.1  n/a   candidat (+)   2   -0.233   10.2.3.4      64     60 10.2.3.4     n/a   outlyer  (-)   2   12.069   192.168.2.2   64     50 172.16.4.5   n/a   candidat (+)   2   -0.958   10.5.6.7      64     50 10.255.34.6  n/a   sys.peer (*)   2   1.713    172.16.3.4    64     45 ``` The following example shows the configured NTP servers and their settings: ```plaintext hostname > show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4 NTP server 3.acme.pool.ntp.org  Enabled: yes  NTP version: 4 ``` ## Configuring NTP authentication using the CLI This topic describes how to configure NTP authentication using the CLI. ### Enabling NTP authentication and configuring keys Perform the tasks in this section in the order shown to configure NTP authentication. Obtain the authentication keys from the NTP server: 1. On the NTP server, map a key ID from 1–16 to an MD5 or SHA1 hash value. 2. Repeat the previous step for additional key ID/value pairs. 3. Copy and paste the key ID/value pairs so they can be configured on the appliance later in this procedure. Enable NTP and NTP authentication: 1. Go to CLI configuration mode: ```plaintext hostname > enable hostname # configure terminal ``` 2. View the current status. ```plaintext hostname (config) # show ntp configured ``` 3. If `NTP enabled: no` appears in the command output, enable NTP. ```plaintext hostname (config) # ntp enable ``` 4. If `NTP Authentication enabled: no` appears is the command output, enable NTP authentication. ```plaintext hostname (config) # ntp authentication enable ``` Define the authentication keys: 1. Use the following command to configure the key ID and hash value you obtained from the NTP server: ```plaintext hostname (config) # ntp authentication key hash ``` where: - `<number>` is an integer from **1**–**16** - `<type>` is **md5** or **sha1** - `<value>` is the hash value 2. Repeat the previous step for each key you want to define. 3. View the configured keys. ```plaintext hostname (config) # show ntp authentication configured ``` 4. Save your changes. ```plaintext hostname (config) # write memory ``` Assign the keys to the NTP servers: 1. To assign a key to an NTP server, use the `ntp server <server> authentication key <number>` command, where `<server>` is the IP address or hostname of the NTP server, and `<number>` is the integer that you assigned to the key in the previous task The following example assigns hash key 1 to the NTP server 0.acme.pool.ntp.org: ```plaintext hostname (config) # ntp server 0.acme.pool.ntp.org authentication key 1 ``` 2. Repeat the previous step for each key you want to define. 3. View the assigned keys: ```plaintext hostname (config) # show ntp configured ``` 4. Verify that the keys are valid: ```plaintext hostname (config) # show ntp authentication ``` 5. Save your changes: ```plaintext hostname (config) # write memory ``` ### Disabling NTP authentication and removing keys You cannot delete an authentication key from the system if it is mapped to an NTP server. If a key is mapped to an NTP server, you must disable NTP authentication on that server before you delete the key. To disable NTP authentication on the system: 1. Go to CLI configuration mode: ```plaintext hostname > enable hostname # configure terminal ``` 2. Disable NTP authentication: ```plaintext hostname (config) # no ntp authentication ``` 3. Save your changes: ```plaintext hostname (config) # write memory ``` To disable NTP authentication on a specific server: 1. Go to CLI configuration mode: ```plaintext hostname > enable hostname # configure terminal ``` 2. To disable NTP authentication with a specified NTP server, use the `no ntp server <server> authentication` command, where `<server>` is the hostname or IP address of the NTP server. The following example disables NTP authentication with the NTP server with hostname 1.acme.pool.ntp.org: ```plaintext hostname (config) # no ntp server 1.acme.pool.ntp.org authentication ``` 3. Save your changes: ```plaintext hostname (config) # write memory ``` To delete an NTP authentication key: 1. Go to CLI configuration mode: ```plaintext hostname > enable hostname # configure terminal ``` 2. To delete a key, use the `no ntp authentication key <number>` command, where `<number>` is the key ID. ```plaintext hostname (config) # no ntp authentication key 1 ``` 3. Save your changes: ```plaintext hostname (config) # write memory ``` #### Examples The following example shows the current configuration. ```plaintext hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` The following example defines two authentication keys and assigns each one to an NTP server. ```plaintext hostname (config) # ntp authentication key 1 hash md5 153ffa51cc765fb257e384e8e6aec8fe ``` ```plaintext hostname (config) # ntp server 0.acme.pool.ntp.org key 1 ``` ```plaintext hostname (config) # ntp authentication key 2 hash sha1 27a048b642be47d50a9c38427495945429597d91 ``` ```plaintext hostname (config) # ntp server 1.acme.pool.ntp.org key 2 hostname (config) # show ntp configured NTP enabled: yes NTP Authentication enabled: yes No NTP peers configured. NTP server 0.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: 1 NTP server 1.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: 2 NTP server 2.acme.pool.ntp.org  Enabled: yes  NTP version: 4  Key: none ``` ```plaintext hostname (config) # show ntp authentication configured NTP enabled: yes NTP Authentication enabled: yes NTP Key Number 1  Type: md5  Key: 153ffa51cc765fb257e384e8e6aec8fe NTP Key Number 2  Type: sha1  Key: 27a048b642be47d50a9c38427495945429597d91 hostname (config) # show ntp authentication NTP is administratively enabled. NTP authentication is administratively enabled. Active servers and peers: Address           auth      keyid ===================================== 172.16.2.3        ok         1 10.30.4.3         ok         2 192.168.10.12     none       none ``` The following example disables NTP authentication on the 1.acme.pool.ntp.org server and then deletes the key it was using from the system. ```plaintext hostname (config) # no ntp server 1.acme.pool.ntp.org authentication hostname (config) # no ntp authentication key 2 ```