--- title: "Performing the initial Central Management configuration using AWS" slug: "performing-the-initial-central-management-configuration-using-aws" tags: ["Endpoint Security (HX)", "Product Usage"] updated: 2026-10-01T09:38:10Z published: 2026-10-01T09:38:10Z canonical: "docs.trellix.com/performing-the-initial-central-management-configuration-using-aws" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Performing the initial Central Management configuration using AWS The management interface is the port through which the Central Management System instance is managed and administered. It is also the port through which integration of the Central Management System instance and managed appliances is managed. Initial settings need to be configured to set up the management interface and to allow access to the network, change the default admin password, and so on. To perform the initial configuration of a Central Management System instance: 1. Connect to the sensor through an SSH client. 2. At the login prompt, enter` admin`. 3. Do one of the following: - Use the` ssh -i `command to use the private key file to establish the SSH session. For example,` ssh -i /path/<my-key-pair>.pem admin@<instance>`. When prompted, change the password using the` username admin password <new password> `command. You will be logged out. Log in again using the new password. - At the password prompt, enter the initial password you configured in [Configuring the activation code and initial Admin password](/network-and-platform/docs/configuring-the-activation-code-and-initial-admin-password-1). 4. Accept the license agreement. The configuration jump-start wizard begins. 5. Answer the wizard questions as described in the following table. ### Important If you want to configure a static IP address instead of using DHCP, see [Configuring a static IP address for the ether1 interface](/network-and-platform/docs/configuring-a-static-ip-address-for-the-ether1-interface-1). ### Note If you enter **yes** in the "Use DHCP on ether1 interface?" step, the ether1 interface will obtain its IP address from the AWS eth0 device. | Step | Response | | --- | --- | | Enter activation code? | Enter the activation code for the appliance. (This step is skipped if you provided the activation code in [Configuring the Activation Code and Initial Admin Password on page 1](/network-and-platform/docs/configuring-the-activation-code-and-initial-admin-password).) | | Hostname? | Enter the hostname for the appliance. | | Admin password? | (Optional) Enter a new administrator password. | | Confirm admin password? | Re-enter the new administrator password. | | Enable remote access for 'admin' user? | Enter **yes** to enable the administrator to log in to the appliance remotely. Enter **no** to disable remote access. | | Use DHCP on ether1 interface? | ### Important See the first two notes preceding this table before responding to this step. Enter **yes** to use Dynamic Host Configuration Protocol (DHCP) to configure the appliance IP address and other network parameters. Enter **no** to manually configure your IP address and network settings. (If you enter **yes**, the zeroconf and static IP addressing steps are skipped.) | | Use zeroconf on ether1 interface? | Enter **yes** to use zero-configuration (zeroconf) networking. Enter **no** to specify a static IP address and network mask. (If you specify **yes**, the next step is skipped.) **NOTE**: Do not use zeroconf on the primary interface. | | Primary IP address and masklen? | Enter the IP address for the management interface in A.B.C.D format and enter the network mask (for example, **1.1.1.2 /24**). ### Note Configure the same values you configured when you launched the instance on AWS. | | Default gateway? | Enter the gateway IP address for the management interface. | | Primary DNS server? | Enter the IP address of the DNS server. | | Domain name? | Enter the domain for the management interface (for example, **it.acme.com**). | | Enable fenet service? | Enter **yes** to enable access to the DTI network. (If you enter **no**, the next three steps are skipped.) | | Enable fenet license update service? | Enter **yes** to enable the licensing service to automatically download your licenses from the DTI network and install them. (If licenses are downloaded and installed successfully, the wizard skips the step that prompts for the product license key and the step that prompts for the security-content updates key.) | | Sync appliance time with fenet? | Enter **yes** to synchronize the appliance time with the DTI server time. If you enabled the licensing service, synchronization prevents a feature from being temporarily unlicensed due to a time gap. The wizard makes three attempts to perform this step before it gives up and moves to the next step. | | Update licenses from fenet? | Enter **yes** to download and install your licenses. The wizard makes three attempts to perform this step before it gives up and moves to the next step. | | Enable NTP? | Enter **yes** to enable automatic time synchronization with one or more Network Time Protocol (NTP) servers. Enter **no** to manually set the time and date on the appliance. (This step is skipped if you entered **yes** in the "Sync appliance time with fenet?" step.) If you enter **no**, specify the time and date in subsequent steps. | | Enable FaaS VPN? | Enter **yes** to enable the appliance to connect to Managed Defense (formerly called Trellix as a Service) over the Internet using a secure SSL VPN connection. (This step is skipped if no MD_ACCESS license is installed.) | | Set time (::)? | Enter the appliance time in Greenwich Mean Time (GMT) (UTC+0). (This step and the next step are skipped if you entered **yes** in the "Sync appliance time with fenet?" or "Enable NTP?" step. | | Set date (//
)? | Enter the appliance date in Greenwich Mean Time (GMT) (UTC+0). | | Enable IPv6? | Enter **yes** to enable IPv6 protocol, which changes network IP routing from IPv4 to IPv6. This step and the next two steps will be automatically performed if you entered **yes** in the "Enable FaaS VPN" step.) | | Enable IPv6 autoconfig (SLAAC) on ether1 interface? | Enter **yes** to enable IPv6 autoconfig on the ether1 (management interface) port. (This step is skipped if you entered **no** in the "Enable IPv6?" step.) | | Enable DHCPv6 on ether1 interface? | Enter **yes** to use DHCPv6 to configure IPv6 hosts with IP addresses. (This step is skipped if you entered **no** in the "Use DHCP on ether1 interface?" or "Enable IPv6?" step.) | | Configure CMS HA? | Enter yes to configure the Central Management System appliance in a high availability (HA) environment. (For the remaining HA configuration steps, see the *Central Management System* *High Availability Guide*.) ### Note Central Management System HA is not supported on all virtual CM models. | | Product license key? | Enter the product license key you obtained from Trellix, or press Enter to install a 15-day evaluation license. (This step and the next step are skipped if you entered **yes** in the "Enable fenet license update service?" step and if licenses were successfully installed as a result.) | | Security-content updates key? | Enter the security-content license key you obtained from Trellix, or press Enter to skip this step and install the license later. | :