--- title: "Performing the initial Virtual Execution configuration using AWS" slug: "performing-the-initial-virtual-execution-configuration-using-aws" tags: ["Endpoint Security (HX)", "Product Usage"] updated: 2026-10-02T13:31:56Z published: 2026-10-02T13:31:56Z canonical: "docs.trellix.com/performing-the-initial-virtual-execution-configuration-using-aws" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Performing the initial Virtual Execution configuration using AWS The management interface is the port through which an appliance is managed and administered. It is also the port through which integration of the Central Management System appliance and the Intelligent Virtual Execution - Server appliance is managed. With the single-port address type, the management interface is also the port through which a managed appliance requests and downloads software updates from the DTI network. Initial settings need to be configured to set up the management interface and to allow access to the network, change the default administrator password, and so on. To perform the initial configuration of a virtual Intelligent Virtual Execution - Server appliance: 1. Connect to the sensor through an SSH client. 2. At the login prompt, enter` admin`. 3. Do one of the following: - Use the` ssh -i `command to use the private key file to establish the SSH session. For example,` ssh -i /path/<my-key-pair>.pem admin@<instance>`. When prompted, change the password using the` username admin password <new password> `command. You will be logged out. Log in again using the new password. - At the password prompt, enter the initial password you configured in [Configuring the activation code and initial Admin password](/network-and-platform/docs/configuring-the-activation-code-and-initial-admin-password-3). 4. Accept the license agreement. The configuration jump-start wizard begins. 5. Answer the wizard questions as described in the following table. ### Important Before you run the jump-start wizard, complete the procedure described in [Configuring a static IP address for the ether1 interface](/network-and-platform/docs/configuring-a-static-ip-address-for-the-ether1-interface-2). | Step | Response | | --- | --- | | Enter activation code? | Enter the activation code for the appliance. (This step is skipped if you provided the activation code in [Configuring the Activation Code and Initial Admin Password](/network-and-platform/docs/configuring-the-activation-code-and-initial-admin-password-3).) | | Hostname? | Enter the hostname for the appliance. | | Admin password? | (Optional) Enter a new administrator password. | | Confirm admin password? | Re-enter the new administrator password. | | Enable remote access for 'admin' user? | Enter **yes** to enable the administrator to log in to the appliance remotely. Enter **no** to disable remote access. | | Use DHCP on ether1 interface? | DHCP is not supported on the management interface. Enter **no** to manually configure your IP address and network settings. | | Use zeroconf on ether1 interface? | Enter **yes** to use zero-configuration (zeroconf) networking. Enter **no** to specify a static IP address and network mask. (If you specify **yes**, the next step is skipped.) **NOTE**: Do not use zeroconf on the primary interface. | | Primary IPv4 address and masklen? | Enter the IP address for the management interface in A.B.C.D format and enter the network mask (for example, **1.1.1.2 /24**). ### Important Configure the same values you configured when you launched the instance on AWS. | | Default gateway? | Enter the gateway IP address for the management interface. | | Primary DNS server? | Enter the IP address of the DNS server. | | Domain name? | Enter the domain for the management interface (for example, **it.acme.com**). | | Enable fenet service? | Enter **yes** to enable access to the DTI network. (If you enter **no**, the next three steps are skipped.) | | Enable fenet license update service? | Enter **yes** to enable the licensing service to automatically download your licenses from the DTI network and install them. (If licenses are downloaded and installed successfully, the wizard skips the step that prompts for the product license key and the step that prompts for the security-content updates key.) | | Sync appliance time with fenet? | Enter **yes** to synchronize the appliance time with the DTI server time. If you enabled the licensing service, synchronization prevents a feature from being temporarily unlicensed due to a time gap. The wizard makes three attempts to perform this step before it gives up and moves to the next step. | | Update licenses from fenet? | Enter **yes** to download and install your licenses. The wizard makes three attempts to perform this step before it gives up and moves to the next step. | | Enable NTP? | Enter **yes** to enable automatic time synchronization with one or more Network Time Protocol (NTP) servers. Enter **no** to manually set the time and date on the appliance. (This step is skipped if you entered **yes** in the "Sync appliance time with fenet?" step.) | | Set time (::)? | Enter the appliance time in Greenwich Mean Time (GMT) (UTC+0). (This step and the next step are skipped if you entered **yes** in the "Sync appliance time with fenet?" or "Enable NTP?" step. | | Set date (//
)? | Enter the appliance date in Greenwich Mean Time (GMT) (UTC+0). | | Enable IPv6? | Enter **no**. IPv6 is not supported on Intelligent Virtual Execution - Server appliances that are nodes in an MVX cluster. | | Submission: Configure interface? | Press Enter to accept ether1 as the interface through which sensors and brokers communicate. | | Submission: Use DHCP on interface? | DHCP is not supported on the submission interface. Enter **no** to manually configure the IP address and network settings. | | Submission: IP address and masklen? | Enter the IP address for the submission interface in A.B.C.D format and enter the network mask (for example, **10.1.1.1 /24**). | | Submission: Default IPv4 gateway? | Enter the IP address for the submission interface default gateway in A.B.C.D format. | | Cluster: Configure interface? | Press Enter to accept ether1 as the interface through which brokers and compute nodes communicate. | | Cluster: Use DHCP on interface? | DHCP is not supported on the cluster interface. Enter **no** to manually configure the address settings. | | Cluster: IP address and masklen? | Enter the IP address for the cluster interface in A.B.C.D format and enter the network mask (for example, **10.1.1.2 /24**). | | Product license key? | Enter the product license key you obtained from Trellix, or press Enter to install a 15-day evaluation license. (This step and the next step are skipped if you entered **yes** in the "Enable fenet license update service?" step and if licenses were successfully installed as a result.) | | Security-content updates key? | Enter the security-content license key you obtained from Trellix, or press Enter to skip this step and install the license later. | :