--- title: "Splitting DTI and management traffic using the CLI" slug: "splitting-dti-and-management-traffic-using-the-cli-2" updated: 2026-08-25T21:18:03Z published: 2026-08-25T21:18:03Z canonical: "docs.trellix.com/splitting-dti-and-management-traffic-using-the-cli-2" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.trellix.com/llms.txt > Use this file to discover all available pages before exploring further. # Splitting DTI and management traffic using the CLI Use the commands in this section to split DTI and management traffic. The following topologies are supported: - [Appliance and managed appliance in same subnet](/network-and-platform/docs/splitting-dti-and-management-traffic-using-the-cli-2#UUID-7bbff855-5caf-f802-aa01-0f41bdb71ce9_id_cm) - [Appliance and managed appliance in different subnets](/network-and-platform/docs/splitting-dti-and-management-traffic-using-the-cli-2#UUID-7bbff855-5caf-f802-aa01-0f41bdb71ce9_id_cm2) ### Central Management System appliance and managed appliance in same subnet To configure split traffic when the devices are in the same subnet: 1. Go to CLI configuration mode: ``` cm-hostname > enable cm-hostname # configure terminal ``` 2. Enable the interface that should have Internet access for DTI traffic: ``` cm-hostname (config) # no interface shutdown ``` where` <interface> `is the name of the interface (for example, `ether4`). 3. Configure the interface for DTI traffic: ``` cm-hostname (config) # interface ip address ``` where `<interface>` is the interface name, `<ipAddress>` is the interface IP address, and `<mask>` is the network mask. The network mask can be specified in a dotted decimal format (such as 255.255.255.0) or in a mask length format (such as /24). 4. Remove the existing default gateway route: ``` cm-hostname (config) # no ip default-gateway ``` 5. Configure the default gateway to the interface for DTI traffic: ``` cm-hostname (config) # ip default-gateway ``` where `<ipAddress>` is the IP address and `<interface>` is the name of the interface for DTI traffic. 6. Verify the default gateway configuration: ``` cm-hostname (config) # show ip default-gateway ``` 7. Verify the IP route: ``` cm-hostname (config) # show ip route ``` 8. Save your changes: ``` cm-hostname (config) # write memory ``` ### Example In this example, the current settings are shown, DTI traffic is configured to go through the ether4 interface, and the configuration is verified. ``` cm-hostname (config) # show ip default-gateway Active default gateways:   172.16.1.1 (interface: ether1) cm-hostname (config) # show ip route Destination     Mask              Gateway          Interface      Source default         0.0.0.0           172.16.1.1       ether1         static 172.16.0.0      255.240.0.0       0.0.0.0          ether1         interface cm-hostname (config) # no interface ether4 shutdown cm-hostname (config) # interface ether4 ip address 10.13.66.12 255.255.255.0 cm-hostname (config) # no ip default-gateway cm-hostname (config) # ip default-gateway 10.13.66.1 ether4 cm-hostname (config) # show ip default-gateway Active default gateways:   10.13.66.1 (interface: ether4) cm-hostname (config) # show ip route Destination     Mask              Gateway          Interface      Source default         0.0.0.0           10.13.66.1       ether4         static 10.13.66.1      255.255.255.0     0.0.0.0          ether4         interface 172.16.0.0      255.240.0.0       0.0.0.0          ether1         interface ``` ### Central Management System appliance and managed appliance in different subnets When the Central Management System appliance and the managed appliance are in different subnets, there is an additional step to configure a static route for the managed appliance to connect to the Central Management System appliance. To configure split traffic when the devices are in different subnets: 1. Go to CLI configuration mode: ``` cm-hostname > enable cm-hostname # configure terminal ``` 2. Enable the interface that should have Internet access for DTI traffic: ``` cm-hostname (config) # no interface shutdown ``` where `<interface>` is the name of the interface (for example, **ether4**). 3. Configure the IP address and netmask of the interface for DTI traffic: ``` cm-hostname (config) # interface ip address ``` where `<interface>` is the name of the interface, `<ipAddress>` is the IP address of that interface, and `<mask>` is the network mask. The network mask can be specified in a dotted decimal format (such as 255.255.255.0) or in a mask length format (such as /24). 4. Remove the static default gateway: ``` cm-hostname (config) # no ip default-gateway ``` 5. Reconfigure the default gateway to the interface for DTI traffic: ``` cm-hostname (config) # ip default-gateway ``` where `<ipAddress>` is the IP address and `<interface>` is the name of the interface for DTI traffic. 6. Add a static route for the Central Management System platform to send management traffic to the managed appliance over the ether1 interface: ``` cm-hostname (config) # ip route ether1 ``` where `<ipAddress>` is an IP address in the same subnet as the managed appliance and `<mask>` is the network mask. 7. Verify the default gateway configuration: ``` cm-hostname (config) # show ip default-gateway ``` 8. Verify the IP route: ``` cm-hostname (config) # show ip route ``` 9. Save your changes: ``` cm-hostname (config) # write memory ``` ###### Example In this example, the current settings are shown, DTI traffic is configured to go through the ether4 interface, a new static route is configured for management traffic, and then the configuration is verified. ``` cm-hostname (config) # show ip default-gateway Active default gateways:   172.16.1.1 (interface: ether1) cm-hostname (config) # show ip route Destination     Mask              Gateway          Interface      Source default         0.0.0.0           172.16.1.1       ether1         static 172.16.0.0      255.240.0.0       0.0.0.0          ether1         interface cm-hostname (config) # no interface ether4 shutdown cm-hostname (config) # interface ether4 ip address 10.13.66.12 255.255.255.0 cm-hostname (config) # no ip default-gateway cm-hostname (config) # ip default-gateway 10.13.66.1 ether4 cm-hostname (config) # ip route 172.17.74.0 255.255.255.0 ether1 cm-hostname (config) # show ip default-gateway Active default gateways:   10.13.66.1 (interface: ether4) cm-hostname (config) # show ip route Destination     Mask              Gateway          Interface      Source default         0.0.0.0           10.13.66.1       ether4         static 10.13.66.1      255.255.255.0     0.0.0.0          ether4         interface 172.16.0.0      255.240.0.0       0.0.0.0          ether1         interface 172.17.74.0     255.255.255.0     0.0.0.0          ether1         static ``` :